Fresh Properties of 3D Printed Mortar with Recycled Powder (2021-10)¶
10.1016/j.conbuildmat.2021.125186
Hou Shaodan, , ,
Journal Article - Construction and Building Materials, Vol. 309
Abstract
In this study, recycled powder (RP) was used to partly replace cement to produce the sustainable 3D printed mortar (3DPM). The properties of fresh 3DPM with RP of different replacement ratio (10%, 20% and 30%) were studied by conventional tests and 3D printer. At first, the flowability, setting time, mechanical property and hydration heat of fresh 3DPM with RP were investigated. Then 3DPM with RP was extruded and built by 3D printer to study the extrudability and buildability. The results show that the incorporation of RP in 3DPM leads to higher flowability losing rate with time, shorter open time, shorter initial and final setting time as well as rapid growth of penetration resistance stress with time. The maximum stress and the Young’s modulus of fresh 3DPM grow linearly with time at a lower replacement ratio, while there is a rapid growth when the replacement ratio is higher than 20%. Compared with 3DPM without RP, the maximum stress and Young’s modulus of 3DPM with 30% RP are increased 226.5% and 252.2% at 180 min, respectively. The addition of RP enhances the heat evolution rate and hydration heat in 8 h after mixing with water. The well correlation of hydration heat and fresh properties is obtained, which indicates that RP can be used in 3DPM to enhance the early age mechanical properties and buildability. 3DPM with 10%-30% RP has good extrudability and buildability.
¶
25 References
- Chen Yu, Li Zhenming, Figueiredo Stefan, Çopuroğlu Oğuzhan et al. (2019-04)
Limestone and Calcined-Clay-Based Sustainable Cementitious Materials for 3D Concrete Printing:
A Fundamental Study of Extrudability and Early-Age Strength Development - Chen Mingxu, Li Laibo, Zheng Yan, Zhao Piqi et al. (2018-09)
Rheological and Mechanical Properties of Admixtures-Modified 3D Printing Sulphoaluminate Cementitious Materials - Ding Tao, Xiao Jianzhuang, Qin Fei, Duan Zhenhua (2020-03)
Mechanical Behavior of 3D Printed Mortar with Recycled Sand at Early-Ages - Figueiredo Stefan, Rodríguez Claudia, Ahmed Zeeshan, Bos Derk et al. (2019-03)
An Approach to Develop Printable Strain-Hardening Cementitious Composites - Ji Guangchao, Ding Tao, Xiao Jianzhuang, Du Shupeng et al. (2019-05)
A 3D Printed Ready-Mixed Concrete Power-Distribution Substation:
Materials and Construction Technology - Le Thanh, Austin Simon, Lim Sungwoo, Buswell Richard et al. (2012-01)
Mix-Design and Fresh Properties for High-Performance Printing Concrete - Long Wujian, Tao Jie-Lin, Lin Can, Gu Yucun et al. (2019-08)
Rheology and Buildability of Sustainable Cement-Based Composites Containing Micro-Crystalline Cellulose for 3D Printing - Ma Guowei, Li Zhijian, Wang Li (2017-12)
Printable Properties of Cementitious Material Containing Copper-Tailings for Extrusion-Based 3D Printing - Ma Guowei, Li Zhijian, Wang Li, Bai Gang (2018-10)
Micro-Cable-Reinforced Geopolymer Composite for Extrusion-Based 3D Printing - Malaeb Zeina, Sakka Fatima, Hamzeh Farook (2019-02)
3D Concrete Printing:
Machine Design, Mix Proportioning, and Mix Comparison Between Different Machine Setups - Nerella Venkatesh, Mechtcherine Viktor (2019-02)
Studying the Printability of Fresh Concrete for Formwork-Free Concrete Onsite 3D Printing Technology (CONPrint3D) - Panda Biranchi, Lim Jian, Tan Ming (2019-02)
Mechanical Properties and Deformation Behavior of Early-Age Concrete in the Context of Digital Construction - Panda Biranchi, Ruan Shaoqin, Unluer Cise, Tan Ming (2018-11)
Improving the 3D Printability of High-Volume Fly-Ash Mixtures via the Use of Nano-Attapulgite-Clay - Panda Biranchi, Tan Ming (2018-11)
Rheological Behavior of High-Volume Fly-Ash Mixtures Containing Micro-Silica for Digital Construction Application - Panda Biranchi, Unluer Cise, Tan Ming (2018-10)
Investigation of the Rheology and Strength of Geopolymer Mixtures for Extrusion-Based 3D Printing - Perrot Arnaud, Rangeard Damien, Nerella Venkatesh, Mechtcherine Viktor (2019-02)
Extrusion of Cement-Based Materials:
An Overview - Rahul Attupurathu, Santhanam Manu, Meena Hitesh, Ghani Zimam (2018-12)
3D Printable Concrete:
Mixture-Design and Test-Methods - Roussel Nicolas (2018-05)
Rheological Requirements for Printable Concretes - Tay Yi, Panda Biranchi, Paul Suvash, Mohamed Nisar et al. (2017-05)
3D Printing Trends in Building and Construction Industry:
A Review - Tay Yi, Qian Ye, Tan Ming (2019-05)
Printability-Region for 3D Concrete Printing Using Slump- and Slump-Flow-Test - Wangler Timothy, Lloret-Fritschi Ena, Reiter Lex, Hack Norman et al. (2016-10)
Digital Concrete:
Opportunities and Challenges - Wolfs Robert, Bos Freek, Salet Theo (2018-02)
Early-Age Mechanical Behaviour of 3D Printed Concrete:
Numerical Modelling and Experimental Testing - Xiao Jianzhuang, Zou Shuai, Yu Ying, Wang Yu et al. (2020-09)
3D Recycled Mortar Printing:
System-Development, Process-Design, Material-Properties and On-Site-Printing - Zhang Yu, Zhang Yunsheng, Liu Guojian, Yang Yonggan et al. (2018-04)
Fresh Properties of a Novel 3D Printing Concrete Ink - Zhang Yu, Zhang Yunsheng, She Wei, Yang Lin et al. (2019-01)
Rheological and Hardened Properties of the High-Thixotropy 3D Printing Concrete
58 Citations
- Tushar Fazlul, Hasan Mehedi, Hasan Kamrul, Mawa Jannatul et al. (2026-01)
Factors Affecting Flowability and Rheological Behavior of 3D Printed Concrete:
A Comprehensive Review - Liu Xuelin, Kong Jiafeng, Chen Yidong, Wang Liang et al. (2025-12)
Rheology and Printability Control of Low-Carbon 3D-Printed Cementitious Materials via Circular Use of Recycled Concrete Powder - Öztürk Ece, Ince Ceren, Borgianni Yuri, Nicolaides Demetris et al. (2025-12)
Printability, Engineering Properties and Environmental Implications of 3D-Printed Cementitious Mortars Incorporating Hydrated Lime, Tile Powder and Accelerator - Sikora Paweł, Federowicz Karol, Skibicki Szymon, Techman Mateusz et al. (2025-11)
Demonstration of 3D-Printed Concrete Containing Fine Recycled Concrete Aggregates and Recycled Concrete Powder:
Rheology, Early-Age, Shrinkage, Mechanical, and Durability Performance. - Sičáková Alena, Verčimák Dominik (2025-11)
Lightweight Mixtures with a High Proportion of Recycled Fillers in Terms of 3D Printing Parameters - Zhang Jiao-Long, Yuan Yong, Fatoyinbo Imoleayo, Zhou Lujie et al. (2025-11)
3D-Printable Mortars Incorporating Municipal Solid Waste Incineration Bottom Ash:
Linking Hydration to Extrudability and Mechanical Performance - González-Aviña J., Hosseinpoor Masoud, Yahia Ammar, Kohandelnia Mojtaba et al. (2025-10)
Anionic Biopolymers to Enhance Concrete Rheological Properties for 3D Printing Applications - Ramakrishnan Sayanthan, Pasupathy Kirubajiny, Manalo Allan, Sanjayan Jay (2025-07)
Rheological, Mechanical and Fire Resistance Performance of Waste Glass Activated Geopolymers for Concrete 3D Printing - Ravichandran Darssni, Prem Prabhat, Bhaskara Gollapalli, Maheswaran Srinivasan et al. (2025-07)
Time-Dependent Properties of 3D Printable Plain and Fibered High Strength Concrete Incorporating Copper Slag as an Alternate Fine Aggregate - Su Yanli, Wu Chang, Shang Jiaqi, Zhang Pu (2025-06)
Mechanical Properties of 3D-Printed High-Ductility Cementitious Composite with Sulphoaluminate Cement and Modified Crumb Rubber - Kumar Sandeep, Kumar Abhishek, Pundir Aakanksha, Dwivedi Ashutosh et al. (2025-06)
Low-Clay Soil as Fine Aggregate in 3D Printed Concrete:
Insights into Fresh and Hardened Properties - Mohamed Osama, Mishra Anamika, Isam Fida (2025-05)
An Overview of 3D Printed Concrete for Building Structures:
Material Properties, Sustainability, Future Opportunities, and Challenges - Liu Xingzi, Xu Jie, Dobrzanski James, Kolawole John et al. (2025-05)
Factors Affecting the Flexural Performance of Reinforced 3D Printed Concrete Beams - Thib Raghed, Taleb Maria, Belayachi Naima, Bulteel David et al. (2025-05)
Hardened Properties of 3D Printable Mortars with Full Replacement of Natural Sand by Recycled Sand - Shen Jianyu, Ye Taohua, Xiao Jianzhuang, Li Shuisheng (2025-04)
Mechanical and Thermal Properties of 3D Printed Earth Concrete Solidified by Geopolymers:
A Study of Utilizing Excavated Clay - Cavalcante Tiago, Toledo Filho Romildo, Mendoza Reales Oscar (2025-04)
Rheological and Environmental Implications of Recycled Concrete Powder as Filler in Concrete 3D Printing - Chen Wei, Pan Jinlong, Zhu Binrong, Han Jinsheng et al. (2025-03)
Nonlinear Predictive Modeling of Building Rates Incorporating Filament Compression Deformations in 3D Printed Geopolymer Concrete - Nasr Ahmed, Duan Zhenhua, Singh Amardeep, Deng Qi et al. (2025-02)
Fresh Properties and Rheological Behavior of 3D-Printed Cementitious Composites Incorporating Recycled PVC and Nylon Fibers:
An Experimental Approach - Yuan Yong, Fatoyinbo Imoleayo, Sheng Ruiyi, Wang Qiling et al. (2025-02)
Advancing the Applicability of Recycled Municipal Solid Waste Incineration Bottom Ash as a Cement Substitute in Printable Concrete:
Emphasis on Rheological and Microstructural Properties - Lyu Qifeng, Wang Yalun, Chen Dongjian, Liu Shiyuan et al. (2025-01)
Energy Storage Properties and Mechanical Strengths of 3D Printed Porous Concrete Structural Supercapacitors Reinforced by Electrodes Made of Carbon-Black-Coated Ni Foam - Du Longyu, Zhou Jiehang, Lai Jianzhong, Yin Xuexiang et al. (2024-12)
Dynamic Damage Behavior and Anisotropic Mechanism of 3D Printed Reinforced Concrete Subjected to Penetration - Chen Yidong, Zhang Yunsheng, Quan Hongzhu, Liu Cheng et al. (2024-10)
Early-Age Time-Dependent Mechanical Properties of 3D Printed Concrete with Coarse Aggregates - Shen Kaige, Ding Tao, Cai Chen, Xiao Jianzhuang et al. (2024-09)
Feasibility-Analysis of 3D Printed Concrete with Sludge-Incineration-Slag:
Mechanical Properties and Environmental Impacts - Chaudhari Ojas, Johansson Jan, Haage Mathias, Sjölander Andreas et al. (2024-09)
3D Printing-Strategy and Implementation for Concrete Prefabrication Industry in Sweden - Tudela Marcell, Cardenas Palomino Kelssy, Bienvenu Sophie, Dunkelberg Federico et al. (2024-09)
Development and Characterization of a Printable Concrete Made with Construction and Demolition-Waste-Aggregates - Hou Shaodan, Wu Wenbo, Duan Zhenhua, Zhou Shuai et al. (2024-09)
Rheology of Fiber-Reinforced Mortar for 3D Printing Construction:
Effect of Recycled Hybrid-Powder and Polyethylene-Fiber - Jia Lutao, Niu Geng, Dong Enlai, Jiang Yifan et al. (2024-08)
Optimization-Strategy for Incorporating Recycled Brick-Powder in 3D Printed Concrete by Balancing Low-Carbon Footprint and Enhanced Performance - Li Bingying, Ding Tao, Qu Changwei, Liu Wei (2024-07)
Modification of Fresh and Hardened Properties of 3D Printed Recycled Mortar by Superabsorbent Polymers - Bai Meiyan, Xiao Jianzhuang, Shen Jianyu, Ding Tao et al. (2024-07)
Printability and Mechanical Anisotropy of 3D Printed Concrete with Manufactured Sand Derived from Basalt - Villiers Wibke, Mwongo Mwiti, Babafemi Adewumi, Zijl Gideon (2024-06)
Quantifying Recycled Construction and Demolition Waste for Use in 3D Printed Concrete - Rahman Mahfuzur, Rawat Sanket, Yang Chunhui, Mahil Ahmed et al. (2024-05)
A Comprehensive Review on Fresh and Rheological Properties of 3D Printable Cementitious Composites - Lyu Qifeng, Wang Yalun, Dai Pengfei (2024-05)
Multilayered Plant-Growing Concrete Manufactured by Aggregate-Bed 3D Concrete Printing - Chen Anguo, Dai Pengfei, Lyu Qifeng (2024-05)
Effect of Alkalized Straw-Fibers on the Properties of Three Dimensional Printed Cementitious Composite - Ma Lei, Jia Zijian, Chen Yuning, Jiang Yifan et al. (2024-03)
Water Loss and Shrinkage Prediction in 3D Printed Concrete with Varying w/b and Specimen Sizes - Soda Prabhath, Dwivedi Ashutosh, Sahana C., Gupta Souradeep (2024-03)
Development of 3D Printable Stabilized Earth-Based Construction Materials Using Excavated Soil:
Evaluation of Fresh and Hardened Properties - Ding Tao, Shen Kaige, Cai Chen, Xiao Jianzhuang et al. (2024-02)
3D Printed Concrete with Sewage Sludge Ash:
Fresh and Hardened Properties - Wang Xiaonan, Li Wengui, Guo Yipu, Kashani Alireza et al. (2024-02)
Concrete 3D Printing Technology in Sustainable Construction:
A Review on Raw Materials, Concrete Types and Performances - Liu Qiong, Cheng Shengbo, Peng Bin, Chen Kailun et al. (2024-01)
The Buildability and Flexural Properties of 3D Printed Recycled Mortar Reinforced with Synchronized Steel-Cable Under Different Reinforcement Ratios - Lucen Hao, Long Li, Shipeng Zhang, Huanghua Zhang et al. (2023-12)
The Synergistic Effect of Greenhouse Gas CO2 and Silica-Fume on the Properties of 3D Printed Mortar - Liu Qiong, Cheng Shengbo, Sun Chang, Chen Kailun et al. (2023-11)
Steel-Cable Bonding in Fresh Mortar and 3D Printed Beam Flexural Behavior - Lyu Qifeng, Dai Pengfei, Chen Anguo (2023-10)
Mechanical Strengths and Optical Properties of Translucent Concrete Manufactured by Mortar-Extrusion 3D Printing with Polymethyl-Methacrylate Fibers - Zhu Binrong, Wang Yufei, Sun Junbo, Wei Yang et al. (2023-10)
An Experimental Study on the Influence of Waste-Rubber-Particles on the Compressive, Flexural and Impact Properties of 3D Printable Sustainable Cementitious Composites - Thib Raghed, Belayachi Naima, Bouarroudj Mohamed, Bulteel David et al. (2023-10)
A Methodology for Designing 3D Printable Mortar Based on Recycled Sand - Lyu Qifeng, Dai Pengfei, Zong Meirong, Zhu Pinghua et al. (2023-10)
Plant-Germination Ability and Mechanical Strength of 3D Printed Vegetation Concrete Bound with Cement and Soil - Luo Fuming, Cui Peng, Tang Wei, Wu Chun-ran et al. (2023-09)
Influences of Engineering Spoil on the Properties and Microstructure of 3D Printable Magnesium-Cement - Ungureanu Dragoș, Onuțu Cătălin, Isopescu Dorina, Țăranu Nicolae et al. (2023-06)
A Novel Approach for 3D Printing Fiber-Reinforced Mortars - Hou Shaodan, Duan Zhenhua, Ye Taohua, Zou Shuai et al. (2023-06)
Mechanical Properties and Pore-Structure of 3D Printed Mortar with Recycled Powder - Lyu Qifeng, Dai Pengfei, Chen Anguo (2023-05)
Sandwich-Structured Porous Concrete Manufactured by Mortar-Extrusion and Aggregate-Bed 3D Printing - Samudrala Manideep, Mujeeb Syed, Lanjewar Bhagyashri, Chippagiri Ravijanya et al. (2023-05)
3D Printable Concrete for Energy-Efficient Buildings - Besklubova Svetlana, Tan Bing, Zhong Ray, Spicek Nikola (2023-04)
Logistic-Cost-Analysis for 3D Printing Construction Projects Using a Multi-Stage Network-Based Approach - Fonseca Mariana, Matos Ana (2023-03)
3D Construction Printing Standing for Sustainability and Circularity:
Material-Level Opportunities - Xiao Jianzhuang, Hou Shaodan, Duan Zhenhua, Zou Shuai (2023-01)
Rheology of 3D Printable Concrete Prepared by Secondary Mixing of Ready-Mix Concrete - Peng Yiming, Unluer Cise (2022-12)
Development of Alternative Cementitious Binders for 3D Printing Applications:
A Critical Review of Progress, Advantages and Challenges - Zhang Chao, Jia Zijian, Luo Zhe, Deng Zhicong et al. (2022-11)
Printability and Pore-Structure of 3D Printing Low-Carbon Concrete Using Recycled Clay-Brick-Powder with Various Particle-Features - Zhang Hanghua, Xiao Jianzhuang, Duan Zhenhua, Zou Shuai et al. (2022-06)
Effects of Printing Paths and Recycled Fines on Drying Shrinkage of 3D Printed Mortar - Klyuev Sergey, Klyuev Alexander, Fediuk Roman, Ageeva Marina et al. (2022-04)
Fresh and Mechanical Properties of Low-Cement Mortars for 3D Printing - Liu Qiang, Jiang Quan, Huang Mojia, Xin Jie et al. (2022-03)
Modifying Effect of Anionic Polyacrylamide Dose for Cement-Based 3DP Materials:
Printability and Mechanical Performance Tests - Yang Huashan, Che Yujun (2022-01)
Recycling of Aggregate Micro-Fines as a Partial Replacement for Fly-Ash in 3D Printing Cementitious Materials
BibTeX
@article{hou_xiao_duan_ma.2021.FPo3PMwRP,
author = "Shaodan Hou and Jianzhuang Xiao and Zhenhua Duan and Guowei Ma",
title = "Fresh Properties of 3D Printed Mortar with Recycled Powder",
doi = "10.1016/j.conbuildmat.2021.125186",
year = "2021",
journal = "Construction and Building Materials",
volume = "309",
}
Formatted Citation
S. Hou, J. Xiao, Z. Duan and G. Ma, “Fresh Properties of 3D Printed Mortar with Recycled Powder”, Construction and Building Materials, vol. 309, 2021, doi: 10.1016/j.conbuildmat.2021.125186.
Hou, Shaodan, Jianzhuang Xiao, Zhenhua Duan, and Guowei Ma. “Fresh Properties of 3D Printed Mortar with Recycled Powder”. Construction and Building Materials 309 (2021). https://doi.org/10.1016/j.conbuildmat.2021.125186.