2025-11¶

1. Iqbal Imtiaz, Kasim Tala, Inqiad Waleed, Besklubova Svetlana et al. (2025-11)
   Effect of Metakaolin and Biochar Addition on the Performance of 3D Concrete Printing:
   A Meta-Analysis Approach
2. Kalmykov Oleg, Reznik Petro, Furman Inna, Demianenko Ivan (2025-11)
   Experimental Testing of a Complex-Geometry Floor Slab Manufactured Using 3DCP Technology
3. Tenesesku Vladyslav (2025-11)
   Technological Aspects of Fabricating a Reinforced Concrete Shell Using 3D Concrete Printing
4. Liu Huawei, Tao Yaxin, Zhu Chao, Liu Chao et al. (2025-11)
   3D Printed Concrete with Recycled Coarse Aggregate:
   Freeze-Thaw Resistance Assessment and Damage Mechanisms
5. Tao Jie-Lin, Hu Shengming, Duan Zhenhua, Jiao Dengwu (2025-11)
   Magneto-Responsive Flow Behavior and Early-Age Microstructural Evolution of 3D Printing Lightweight Concrete with Fly Ash Cenospheres
6. Mansouri Abraham, Mourad Bahaa, Birhane Bezawit, Denbel Nuhamin et al. (2025-11)
   Noncontact Measurement of Thermal Resistance in 3D Concrete Printing Building Envelopes Using Infrared Sensing and Arduino
7. Si Wen, Khan Mehran, McNally Ciaran (2025-11)
   Rheological Optimization and Mechanical Performance Assessment of High-Volume GGBS-Silica Fume Mortars for 3D Printing
8. Li Chenglin, Jiao Y., Ren Kai, Liu N. et al. (2025-11)
   A Novel Pivot-Move Strategy for Dual-Robot Manipulator Additive Manufacturing:
   Enabling Collision Avoidance Without Halting Deposition
9. Abbas Yassir, Alsaif Abdulaziz (2025-11)
   Explainable Data-Driven Modeling for Optimized Mix Design of 3D-Printed Concrete:
   Interpreting Nonlinear Synergies Among Binder Components and Proportions
10. Saravanan Pradeep, Ramaswamy Ananth (2025-11)
    Modelling Buildability Performance of 3D Printable Cementitious Materials Using Chemo-Mechanical Model
11. Wang Zherui, Teitelbaum E., Akbarzadeh Masoud, Aviv D. (2025-11)
    Experimental Assessment on Thermal Mass Performance of Structurally Optimized, 3D-Printed Concrete Floor Element for Carbon Emission Reduction
12. Álvarez Luisa, Fernandez Brian, Saldarriaga Federico, Romero Héctor et al. (2025-11)
    Development and Bioclimatic Evaluation of Parametrically Designed Geometries for 3D-Printed Concrete Walls
13. Anastassiou Richard, Alvarado Rodrigo, Wegertseder Martínez Paulina (2025-11)
    Towards Climatomorphism:
    A Generative Optimization Framework for Climate-Adaptive 3D-Printed Free-Form Housing
14. Fasihi Ali, Libre Nicolas (2025-11)
    Tip Penetration Test for Rapid in-Line Assessment of Static Yield Stress During 3D Concrete Printing Process
15. Özdemir Salih, Alaçam Sema (2025-11)
    Cognitive Ecosystem for Lifecycle-Adaptive and Sustainable 3D Concrete Printing
16. Ruiz Pedro, Moreno Inna, Alvarado Rodrigo (2025-11)
    On the Tectonic Properties of 3D Printed Architecture:
    On the Tectonic Properties of 3D Printed Architecture
17. Ruiz Pedro, Perez Pablo, Alvarado Rodrigo, Valenzuela Sebastián et al. (2025-11)
    3D Printing of Surrealist Dreams:
    Constraints, Failures, and Craftsmanship in 1:1 Digital Fabrication
18. Sikora Paweł, Federowicz Karol, Skibicki Szymon, Techman Mateusz et al. (2025-11)
    Demonstration of 3D-Printed Concrete Containing Fine Recycled Concrete Aggregates and Recycled Concrete Powder:
    Rheology, Early-Age, Shrinkage, Mechanical, and Durability Performance.
19. Solaiappan Kamesh, Foruzanmehr M. (2025-11)
    A Rheological Test Method for Determining the Printability Zone of Cementitious 3D Printers
20. Vargas José, Breseghello Luca, Silfwerbrand Johan (2025-11)
    Circular Hybrid Façades:
    Responsive Design of Thermally Efficient 3D Printed Concrete Skins on Reused Concrete Elements
21. Geng Renyu, Jiang Jinming, Du Pengcong, Zhang Huiliang et al. (2025-11)
    Multiscale Thermal Optimization of 3D-Printed Walls:
    Integrating Structure, Material, and Process with Fire-Thermal Synergy
22. Meier Niklas, Herding Friedrich, Zetzener Harald, Mai (née Dressler) Inka et al. (2025-11)
    Surface Modification of Bulk Material for Particle Bed 3D Concrete Printing:
    Effect on Wettability, Porosity, and Mechanical Properties
23. Nguyen Trang, Park Jaejun, Kim Dong-Hyun (2025-11)
    Impacts of Infill Patterns and Curve Types in 3D Printed Clay Walls
24. Yu Hao, Zhang Weiwei, Liew Jia, Yin Binbin et al. (2025-11)
    Simulating Material Flow and Extrusion Dynamics in 3D Concrete Printing
25. Davar Saeed, Ma Zhanguo (2025-11)
    Improving the Mechanical Performance of 3D-Printed UHPFRC with Thermally Modified Carbon Fibers
26. Tulliani Jean-Marc (2025-11)
    Latest Developments in 3D-Printed Engineered Cementitious Composites:
    Technologies, Prospects, and Challenges
27. Gümrük Idil, Schröder Torsten, Wolfs Robert, Salet Theo (2025-11)
    3DCP-CI:
    Developing a Circularity Indicator for Assessing 3DConcrete Printed Architectural Designs
28. Soshinskiy Olexander, Rashkevich Nina, Shakhov Stanislav, Melnychenko Andrii (2025-11)
    Formulating a Calculation Methodology for Assessing the Strength Characteristics of Building Structures Constructed with a Construction 3D Printer
29. Athira R., Sathyan Dhanya (2025-11)
    Review of 3D Printing Advancements in Geopolymer Concrete:
    Current Challenges and Future Directions
30. Bawab Jad, Dieb Amr, Hassan Hilal (2025-11)
    Preliminary Investigation into the Development of Cement-Free Composites Using Emerging Alternatives for 3D Printing
31. Biswas Rajib, Saito Takahiro, Ito Atsushi (2025-11)
    Experimental Evaluation of a Novel 3D-Printed Permanent Concrete Formwork
32. Ebiloma David, Olatunbosun Olajumoke, Isang Inimbom, Aigbavboa Clinton (2025-11)
    Assessing the Effects of 3D-Printed Concrete for Sustainable Construction:
    The Stakeholders' Perspective
33. Ghodke Swapnil, Singh Bhupinder, Chowdhury Shubhankar (2025-11)
    Some Insights on Role of Water Film-Thickness in Rheology of Coarse Aggregate-Based 3D Printable Concrete
34. Khoury Eliane, Cheikh Khadija, Schutter Geert, Cazacliu Bogdan et al. (2025-11)
    Using Vacuum Mixing for 3D Printing of Mortars Made with Recycled Sand
35. Korol Ewelina, Jenta Arkadiusz, Chaudhari Ojas, Wójcik Michal (2025-11)
    Experimental Investigation of Concrete Beams Under Bending, Manufactured with 3D Additive Printing Technology
36. Ma Jiayue, Samarasinghe Don, Rotimi James, Zuo Kelvin (2025-11)
    Establishing Research Methods for 3D Concrete Printing Supply Chain Studies:
    Insights from Literature and Practice
37. Manickavasakam Karnan, Huri Mohammed, Kharma Khaled, Hosan Anwar et al. (2025-11)
    Smart 3D-Printed Concrete:
    Recent Advances in Self-Sensing Mix Design and Functional Reinforcements
38. Sičáková Alena, Verčimák Dominik (2025-11)
    Lightweight Mixtures with a High Proportion of Recycled Fillers in Terms of 3D Printing Parameters
39. Xia Chen, Lee Chang, Leifer Max, Zheng Bujingda (2025-11)
    Additive Reinforced Concrete for Multifunctional Construction Component
40. Patel Aniket, Tripathi Avinaya, Kiran Ravi, Santhanam Manu et al. (2025-11)
    Decoupling Early-Age Free Shrinkage and Restraint Effects in 3D Printed Concrete Using Digital Image Correlation
41. Raza Ali, Tan Binglin, Jiajia Zhou, Umar Muhammad et al. (2025-11)
    Evaluation of Mechanical and Microstructural Properties of Sustainable 3D-Printed Engineered Cementitious Composites Incorporating Hybrid PE/PVA Fibers and Yellow River Sand
42. Zhou Jiehang, Du Longyu, Wu Kai, Lai Jianzhong et al. (2025-11)
    Effective Factors and a Prediction Method on Extrusion Flow of 3D Printed Concrete
43. Benz Hendrik, Nguyen Trong The, Klemt-Albert Katharina (2025-11)
    Real-Time Vision-Based Defect Detection for Large-Scale on-Site Earthen Additive Manufacturing:
    Annotated Dataset and Dual-Model Framework
44. Li Jiannan, Singh Amardeep, Zhao Yasong, Sun Jingting et al. (2025-11)
    Enhancing Thermo-Mechanical and Moisture Properties of 3D-Printed Concrete Through Recycled Ultra-Fine Waste Glass Powder:
    Corrigendum
45. Liu Xianda, Sun Junbo, Chen Hui, Liu Chang et al. (2025-11)
    3D Printed Concrete with Red Mud Incorporation:
    Influence of Red Mud Manufacturing Procedures on Mechanical Properties at Elevated Temperatures
46. Najm-Eddine Asmae, Abouelmajd Mohamed, Najm-Eddine Youssef, Erritali Ilham et al. (2025-11)
    Topological Optimization in 3D Concrete Printing Structures:
    A Review
47. Oh Sangwoo, Lee Jinsuk, Oh Gyujong, Choi Seongcheol (2025-11)
    Effects of the Combined Incorporation of Superabsorbent Polymers and Polyvinyl Alcohol Fibers on Material Properties of 3D Printable Mortar:
    Rheology, Shrinkage, and Mechanical Behavior
48. Tang Can, Zhou Yujie, Mehmood Awais, Rania Chlihi et al. (2025-11)
    A Novel 3D-Printed Negative Poisson's Ratio Grid-Reinforced Cement-Based Composite Wall Structure:
    Design, Fabrication, and Compressive Properties
49. Baah Thomas, Kim Heejeong, Latypov Marat (2025-11)
    Multi-Objective Adaptive Experimental Approach for Optimizing 3D Concrete Printing Mixtures and Parameters Incorporating Construction and Demolition Waste for Sustainable Construction
50. Banijamali Kasra, Martin Michael, Mascarenas David, Kazemian Ali (2025-11)
    Automated Inspection in Robotic 3D Printing:
    In-Process Geometrical Measurements Using Structured Light Machine Vision
51. Zhao Yu, Shen Guanghai, Zhu Lingli, Ding Yahong et al. (2025-11)
    Multi-Scale Analysis of 3D Printable High-Strength Engineered Cementitious Composite with Carbon and Polyethylene Fibers:
    Rheology, Printability and Hydration Kinetics in Structural Components
52. Hasan Md, Xu Jie, Uddin Md (2025-11)
    A Critical Review of 3D Printed Fiber-Based Geopolymer Concrete:
    Fresh Properties, Mechanical Performance, and Current Limitations
53. Li Shiping, Sun Yan, Qian Ye, Chen Wujun et al. (2025-11)
    Bio-Inspired Jigsaw-Interlocking Suture Interfaces for Enhanced Flexural Response of 3D-Printed Strain-Hardening Cementitious Composites
54. Sun Yan, Du Guoqiang, Mudasir Maryam (2025-11)
    Rheological Investigations of Fresh Fiber-Reinforced Cementitious Composites Using Hydrophobic / Hydrophilic UHMWPE Fibers for 3D Concrete Printing Evaluation
55. Abidi Imene, Tuna Meral, Carboni Biagio, Trovalusci Patrizia (2025-11)
    A Parametric Study on Topology Optimization of Additively Manufactured Clay Materials
56. Zhang Jiao-Long, Yuan Yong, Fatoyinbo Imoleayo, Zhou Lujie et al. (2025-11)
    3D-Printable Mortars Incorporating Municipal Solid Waste Incineration Bottom Ash:
    Linking Hydration to Extrudability and Mechanical Performance
57. Adeel Muhammad (2025-11)
    Three-Dimensional Concrete Printing for Sustainable Construction and Architecture:
    A Comprehensive Review
58. Khalid Lawand, Mermerdaş Kasım, Ekmen Şevin, Khidhir Bzeni Dillshad (2025-11)
    Optimization of Fresh and Hardened Properties of Fiber-Reinforced 3D Printed Geopolymer Composites Using Response Surface Methodology:
    A Data-Driven Approach Based on Prior Experimental Studies
59. Bates Rhys, Aslani Farhad (2025-11)
    Performance of 3D-Printed Concrete Columns with GFRP Rebars Under Axial Compression
60. Givkashi Mohammad (2025-11)
    Durability of 3D Printed Concrete Containing Air-Entraining Agent:
    Evaluating the Importance of Carbonation Resistance
61. Lim Sean, Lee Junghyun, Bawarith Nuran, Paul Suvash et al. (2025-11)
    The Efficacy of Self-Curing Agents on Enhanced Internal Curing and Accelerated Carbonation with CO2-Steam Integrated 3D Concrete Printing
62. Megahed Mai, Abou Zeid Mohamed (2025-11)
    Toward Sustainable 3D Concrete Printing:
    Assessment of SCM-Superplasticizer Interactions on Rheology and Buildability
63. Silva Neesha, Rajapaksha Upendra, Udawattha Chameera (2025-11)
    Tailoring 3D Printing for Personalized Housing:
    Selecting the Right Technology for Custom Home Construction
64. Zeng Jun-Jie, Jiang Yuan, Yan Zitong, Sun Hou-Qi et al. (2025-11)
    3D Printing of Continuous Carbon Fiber-Reinforced Polymer Reinforcement for Concrete Columns
65. Zhu Binrong, Liu Xuhua, Wei Yang, Pan Jinlong (2025-11)
    Predicting the Tensile Performance of 3D-Printed PE Fiber-Reinforced ECC Based on Micromechanics Model
66. Lu Qi, Hua Sudong, Yue Hongfei (2025-11)
    Effect of Spherical Electric Arc Slag on Solid Waste-Based 3D-Printed Concrete
67. Song Qiang, Zhou Guangyu, Bao Hailing, Liu Qiong (2025-11)
    Study on the Effects of Nozzle Proximal Carbonation Mixing and Vacuum Dewatering on the Printability and Mechanical Properties of the 3D Printed Construction Mortar
68. Xu Shuhao, Lin Xing-Tao, Chen Xiangsheng (2025-11)
    Numerical Investigation of Anisotropic in 3D Printed Concrete Specimens Considering the Effects of Weak Interfaces and Pore-Induced Defects
69. Diggs-McGee Brandy, Samouh Hamza, Garg Nishant (2025-11)
    Predicting Cementitious Set Times via Infrared Thermography:
    Potential Implications on Real-Time Quality Control During 3D Concrete Printing
70. Zhu Xiaowei, Zhang Xudong, Zhang Jicheng, Chen Miao et al. (2025-11)
    Study on Anisotropic Thermal and Mechanical Properties of 3D-Printed Scrap-Aerogel-Incorporated Concrete
71. Nakase Kota, Zhou Yubao, Hashimoto Katsufumi, Sugiyama Takafumi et al. (2025-11)
    Acoustic Emission Monitoring of Fracture Behaviour of 3D Printed Concrete with Different Printing Paths
72. Pandum Jeero, Hashimoto Katsufumi, Sugiyama Takafumi, Nakase Kota (2025-11)
    AI-Driven Evaluation of 3D-Printed Concrete:
    Analyzing Printed Patterns Using Impact-Echo and Acoustic Emission
73. Sun Yuhang, Li Chuang, Liu Xiongfei, Wang Li et al. (2025-11)
    Enhancing Sulfate Resistance of Spray-Based 3D Printed Recycled Tunnel Slag Concrete Through Polypropylene Fiber Optimization
74. Changez Kashif, Aslam Jawad, Bhutta Muhammad, Butt Shahid (2025-11)
    Hybrid Additive Strategies for Sustainable 3D Concrete Printing:
    Balancing Printability, Early-Stage Strength, and Eco-Efficiency
75. Liu Xiongfei, Wang Haonan, Chen Jinnan, Sun Yuhang et al. (2025-11)
    Fiber Orientation Control in Spray-Based 3D Printed Steel Fiber Reinforced Concrete
76. Maroszek Marcin, Rudziewicz Magdalena, Shah Syed, Tran Doan et al. (2025-11)
    Development of Eco-Friendly Construction Materials for 3D Printing Using Fly Ash and Demolition Waste
77. Xue Jia-Chen, Wang Wei-Chien, Lee Ming-Gin, Huang Chia-Yun et al. (2025-11)
    Examining the Multi-Scale Toughening Mechanisms and Mechanical Anisotropic Behavior of 3D Printed Concrete Reinforced with Calcium Sulfate Whiskers and Mixed Fibers
78. Zhang Hui, Wu Jie, Huang Bo-Tao, Yu Rena et al. (2025-11)
    Cross-Scale Mechanisms of Anisotropy in 3D-Printed Ultra-High-Performance Concrete
79. Abedi Mohammadmadhi, Waris Muhammad, Alawi Mubarak, Jabri Khalifa et al. (2025-11)
    Data-Driven Design of Sustainable LC³ for 3D Printing with Omani Clays
80. Chen Wenguang, Yu Jie, Ye Junhong, Yu Jiangtao et al. (2025-11)
    3D Printed High-Performance Fiber-Reinforced Cementitious Composites:
    Fresh, Mechanical, and Microstructural Properties
81. Flor Juncal Luis, Scott Allan, Clucas Don, Loporcaro Giuseppe (2025-11)
    Influence of Alternative Supplementary Cementitious Materials and Printing Parameters on the Mechanical Properties of 3D-Printed Mortars
82. Sahu Akshay, Panda Biranchi (2025-11)
    An Additive Manufacturing-Oriented Design Approach for Digital Construction
83. Sakolaree Natthanicha, Taweesint Jutamas, Sungsiri Krisana, Assawamankongcharoen Sirikamol et al. (2025-11)
    Evaluation of Fresh and Mechanical Properties and Shrinkage of Hydrophobic Mortar Containing Microfiber for 3D Printing Technology
84. Türk Ayşe, Türk Furkan, Edebali Serpil, Keskin Ülkü (2025-11)
    3D Printable Mortars with Green Materials:
    Sustainable Solutions with Nanocellulose
85. Janani Parthiban, Ganesh G. (2025-11)
    Synergistic Effects of Polypropylene Fibers on the Strength and Durability Properties of 3D Printed Concrete
86. Assi Lateef, Alsalman Ali, Kareem Rahman, Carter Kealy (2025-11)
    Advantages and Challenges of 3D Geopolymer-Based Concrete in Construction
87. Dörrie Robin, Lachmayer Lukas, Baghdadi Abtin, David Martin et al. (2025-11)
    Investigation on Process Guidelines and Geometric Capabilities for Robust Shotcrete 3D Printing
88. Faleschini Flora, Trento Daniel, Zanini Mariano (2025-11)
    Earth as a Building Material:
    From Traditional Building Techniques to Additive Manufacturing
89. Hasani Alireza, Dorafshan Sattar (2025-11)
    Evaluation of Fresh, Hardened, and Durability Properties of Three-Dimensional Concrete Printed Pipes
90. Mani Aravindhraj, Sekar Muthu (2025-11)
    Extrudability in 3D Printing:
    A Comprehensive Approach to S/C, W/C Ratios and Superplasticizer Content
91. Matos Ana, Milheiro-Oliveira Paula, Varum Humberto (2025-11)
    New Technologies for Earth Construction:
    3D Printing, a Reality or a Mirage?
92. Tang Jiyu, Wang Zhihang, Gao Danying, Yang Lin et al. (2025-11)
    Research Progress on 3D Printed Geopolymer Concrete
93. Thib Raghed, Rémond Sébastien, Belayachi Naima, Rémond Elise et al. (2025-11)
    3D Printable Eco-Efficient Mortars Under Salt Water:
    Mix Design and Characterization