Effects of Interval Time and Interfacial Agents on the Mechanical Characteristics of Ultra-High-Toughness Cementitious Composites Under 3D Printed Technology (2023-03)¶

10.1016/j.conbuildmat.2023.130936

Luo Surong, Lin Qian, Xu Wei, Wang Dehui
Journal Article - Construction and Building Materials, Vol. 374

Abstract

Anisotropic mechanical characteristics are crucial to the application of the printed structure. This study is aimed to investigate the effects of interval time and interfacial agents on the anisotropic mechanical strength of ultrahigh toughness cementitious composite under 3D-printed technology. The bending capacity of ultra-high toughness cementitious composite under 3D-printed technology was compared with mould-casting ultra-high toughness cementitious composite. The compressive strength, flexural strength and splitting tensile strength were measured to represent mechanical properties in different directions and the microstructure of ultra-high toughness cementitious composite under 3D-printed technology with different interval time and interfacial agents were characterized using nanoindentation, scanning electron microscopy, and X-ray computed tomography. The experimental results indicated that the ultimate bending strength and bending toughness of ultra-high toughness cementitious composite under 3D-printed technology were 13.6% and 3.3% to 13.3% higher than those of mould-casting ultra-high toughness cementitious composite at 28 d, respectively. As the interval time increased, the mechanical properties showed differential development patterns. Specifically, compressive strength and splitting tensile strength had a higher rate of decline in the X direction (parallel to the printing path) than in the Y and Z directions but flexural strength was the opposite. A 3-h interval time reduced the 28d compressive strength and splitting tensile strength in the X direction by 24.02% and 49.64% but the strength only decreased by 10.57% and 26.59% in the Z-direction. The addition of interfacial agents reduced anisotropy in compressive strength and splitting tensile strength but increased the anisotropy of flexural strength. When the interval time was 3 h, the increase rate of the 28-d flexural strength in the X direction, in which the flexural strength was weakest, was 22%–29% lower than that in the Y and Z directions under the effects of interfacial agents. A microstructure analysis showed that the filling effect and high moisture content of interfacial agents counteracted the negative impact of interval time on the width of the interface between layers and the porosity of ultra-high toughness cementitious composite under 3D-printed technology, which can enhance the interlayer bonding. These results can promote the application of ultra-high toughness cementitious composite under 3D-printed technology in additive manufacturing.

¶

40 References

20 Citations

BibTeX

@article{luo_lin_xu_wang.2023.EoITaIAotMCoUHTCCU3PT,
  author            = "Surong Luo and Qian Lin and Wei Xu and Dehui Wang",
  title             = "Effects of Interval Time and Interfacial Agents on the Mechanical Characteristics of Ultra-High-Toughness Cementitious Composites Under 3D Printed Technology",
  doi               = "10.1016/j.conbuildmat.2023.130936",
  year              = "2023",
  journal           = "Construction and Building Materials",
  volume            = "374",
}

Formatted Citation

IEEE

S. Luo, Q. Lin, W. Xu and D. Wang, “Effects of Interval Time and Interfacial Agents on the Mechanical Characteristics of Ultra-High-Toughness Cementitious Composites Under 3D Printed Technology”, Construction and Building Materials, vol. 374, 2023, doi: 10.1016/j.conbuildmat.2023.130936.

CMOS

Luo, Surong, Qian Lin, Wei Xu, and Dehui Wang. “Effects of Interval Time and Interfacial Agents on the Mechanical Characteristics of Ultra-High-Toughness Cementitious Composites Under 3D Printed Technology”. Construction and Building Materials 374 (2023). https://doi.org/10.1016/j.conbuildmat.2023.130936.