3D Cement Printing (2022-12)¶
Sadakorn Wannapol, Prasertsuk Santirak,
Contribution - Proceedings of 5th International Conference on Civil Engineering and Architecture, pp. 19-28
Abstract
Cement-based materials are widely used materials in today's construction industry because of its durability and strength. However, there were practical challenges of using them as construction materials such as errors by craftsmen, construction time, and many wastes from construction process. The latest technology is becoming an important key in the construction industry in a near future is 3D printing technology with cement-based materials that can eliminate the practical challenges in terms of the operational cost and the construction time during construction process. This research aims to study the Design for Manufacture and Assembly (DFMA) process of 3D printing technology with cement-based system. The study program includes testing the strength performance of the load-bearing walls with geometric patterns. The results of the research were the DFMA guidelines to minimize the practical challenges and operational costs of construction. The knowledge of applying 3D printing technology using cement-based system was established for developing the DFMA guidelines for small residential houses.
¶
16 References
- Ali Md., Issayev Gani, Shehab Essam, Sarfraz Shoaib (2022-02)
A Critical Review of 3D Printing and Digital Manufacturing in Construction Engineering - Daungwilailuk Totsawat, Pheinsusom Phoonsak, Pansuk Withit (2021-01)
Uniaxial Load Testing of Large-Scale 3D Printed Concrete Wall and Finite-Element-Model-Analysis - Dorn Tobias, Hirsch Tamino, Stephan Dietmar (2019-09)
Study on the Influence of Accelerators on the Hydration of Portland Cement and Their Applicability in 3D Printing - Holt Camille, Edwards Laurie, Keyte Louise, Moghaddam Farzad et al. (2019-02)
Construction 3D Printing - Jiramarootapong Patiphat, Prasittisopin Lapyote, Snguanyat Chalermwut, Tanapornraweekit Ganchai et al. (2020-07)
Load Carrying Capacity and Failure Mode of 3D Printing Mortar Wall Panel Under Axial Compression Loading - Long Wujian, Tao Jie-Lin, Lin Can, Gu Yucun et al. (2019-08)
Rheology and Buildability of Sustainable Cement-Based Composites Containing Micro-Crystalline Cellulose for 3D Printing - Ma Guowei, A Ruhan, Xie Panpan, Pan Zhu et al. (2022-01)
3D Printable Aerogel-Incorporated Concrete:
Anisotropy Influence on Physical, Mechanical, and Thermal Insulation Properties - Perrot Arnaud, Jacquet Yohan, Rangeard Damien, Courteille Eric et al. (2020-03)
Nailing of Layers:
A Promising Way to Reinforce Concrete 3D Printing Structures - Prasittisopin Lapyote, Pongpaisanseree Kittisak, Jiramarootapong Patiphat, Snguanyat Chalermwut (2020-07)
Thermal- and Sound-Insulation of Large-Scale 3D Extrusion-Printing Wall-Panel - Prasittisopin Lapyote, Sakdanaraseth Thanut, Horayangkura Vimolsiddhi (2021-06)
Design and Construction Method of a 3D Concrete Printing Self-Supporting Curvi-Linear Pavilion - Sayegh Sameh, Romdhane Lotfi, Manjikian Solair (2022-03)
A Critical Review of 3D Printing in Construction:
Benefits, Challenges, and Risks - Sun Jingting, Xiao Jianzhuang, Li Zhengrong, Feng Xiwen (2021-03)
Experimental Study on the Thermal Performance of a 3D Printed Concrete Prototype Building - Weng Yiwei, Li Mingyang, Ruan Shaoqin, Wong Teck et al. (2020-03)
Comparative Economic, Environmental and Productivity-Assessment of a Concrete Bathroom Unit Fabricated Through 3D Printing and a Pre-Cast Approach - Xiao Jianzhuang, Ji Guangchao, Zhang Yamei, Ma Guowei et al. (2021-06)
Large-Scale 3D Printing Concrete Technology:
Current Status and Future Opportunities - Xiao Jianzhuang, Liu Haoran, Ding Tao (2020-11)
Finite-Element-Analysis on the Anisotropic Behavior of 3D Printed Concrete under Compression and Flexure - Zhang Yu, Zhang Yunsheng, Yang Lin, Liu Guojian et al. (2021-02)
Hardened Properties and Durability of Large-Scale 3D Printed Cement-Based Materials
5 Citations
- Banihashemi Saeed, Akbarnezhad Ali, Sheikhkhoshkar Moslem, Haouzi Hind et al. (2025-08)
3D Printing in Construction:
Sustainable Technology for Building Industry - Sakhare Vishakha, Khairnar Neha, Dahatonde Ulka, Mashalkar Shilpa (2025-06)
Review on Sustainability in 3D Concrete Printing:
Focus on Waste Utilization and Life Cycle Assessment - Suphunsaeng Kantawich, Prasittisopin Lapyote, Pethrung Sirichai, Pansuk Withit (2025-03)
Fire Performance Evaluation of 3D-Printed Concrete Walls:
A Combined Full-Scale and Numerical Modeling Approach - Prasittisopin Lapyote (2024-11)
How 3D Printing Technology Makes Cities Smarter:
A Review, Thematic Analysis, and Perspectives - Tuvayanond Wiput, Prasittisopin Lapyote (2023-02)
Design for Manufacture and Assembly of Digital Fabrication and Additive Manufacturing in Construction:
A Review
BibTeX
@inproceedings{sada_pras_pras.2024.3CP,
author = "Wannapol Sadakorn and Santirak Prasertsuk and Lapyote Prasittisopin",
title = "3D Cement Printing: DFMA Guideline of Patterned Load-Bearing Walls for Small Residential Units",
doi = "10.1007/978-981-99-4049-3_2",
year = "2024",
volume = "369",
pages = "19--28",
booktitle = "Proceedings of 5th International Conference on Civil Engineering and Architecture",
editor = "Thomas Kang",
}
Formatted Citation
W. Sadakorn, S. Prasertsuk and L. Prasittisopin, “3D Cement Printing: DFMA Guideline of Patterned Load-Bearing Walls for Small Residential Units”, in Proceedings of 5th International Conference on Civil Engineering and Architecture, 2024, vol. 369, pp. 19–28. doi: 10.1007/978-981-99-4049-3_2.
Sadakorn, Wannapol, Santirak Prasertsuk, and Lapyote Prasittisopin. “3D Cement Printing: DFMA Guideline of Patterned Load-Bearing Walls for Small Residential Units”. In Proceedings of 5th International Conference on Civil Engineering and Architecture, edited by Thomas Kang, 369:19–28, 2024. https://doi.org/10.1007/978-981-99-4049-3_2.