Ducoulombier Nicolas¶

1. Gribonval Alice, Pierre Maxime, Ducoulombier Nicolas, Sab Karam et al. (2025-05)
   Multi-Physics Modelling of 3D-Printed Concrete Evolution in Environmental Conditions
2. Caron Jean-François, Ducoulombier Nicolas, Demont Léo (2025-01)
   Reinforcement of Printed Structures
3. Ducoulombier Nicolas, Bono Victor, Kachkouch Fatima, Jacquet Yohan et al. (2025-01)
   From Laboratory to Practice
4. Demont Léo, Bono Victor, Ducoulombier Nicolas, Mesnil Romain et al. (2024-11)
   Anisotropic Concrete:
   A Composite Look on the Engineering and Architecture of Concrete Construction
5. Bono Victor, Ducoulombier Nicolas, Loulha Sarena, Mesnil Romain et al. (2024-11)
   Toward 3D Printable Low-Carbon Mortar:
   Method and Application
6. Bono Victor, Demont Léo, Ducoulombier Nicolas, Mesnil Romain et al. (2024-09)
   Large-Scale 3D Printing of a Shell Structure Reinforced by the Flow-Based Pultrusion Process
7. Bono Victor, Ducoulombier Nicolas, Mesnil Romain, Caron Jean-François (2024-09)
   Tailored Low-Carbon Footprint Cementitious Material for 3D Printing:
   Strategies for Rheology Adjustment and Mechanical Performance Estimation
8. Farra Ramzi, Mazanec Oliver, Ducoulombier Nicolas, Mallet Alban (2024-09)
   Toward the Optimal Use of Local Cementitious Materials Through Novel Admixture-Technology and a Dedicated 2K-Printing-System
9. Perrot Arnaud, Jacquet Yohan, Caron Jean-François, Mesnil Romain et al. (2024-08)
   Snapshot on 3D Printing with Alternative Binders and Materials:
   Earth, Geopolymers, Gypsum and Low-Carbon Concrete
10. Wolfs Robert, Bos Derk, Caron Jean-François, Gerke Markus et al. (2024-08)
    On-Line and In-Line Quality-Assessment Across All Scale Levels of 3D Concrete Printing
11. Bono Victor, Mesnil Romain, Ducoulombier Nicolas, Caron Jean-François (2024-08)
    Design, Structural Optimization and Fabrication of Concrete Shell Through Fiber-Reinforced 3D Printing
12. Caron Jean-François, Ducoulombier Nicolas, Demont Léo, Bono Victor et al. (2024-06)
    Reinvent Reinforced Concrete with Robotics and 3D Printing
13. Bono Victor, Ducoulombier Nicolas, Mesnil Romain, Caron Jean-François (2023-12)
    Methodology for Formulating Low-Carbon Printable Mortar Through Particles-Packing-Optimization
14. Caron Jean-François, Ducoulombier Nicolas, Demont Léo, Bono Victor et al. (2023-10)
    3D Printing of Continuous-Fibers Cementitious Composites:
    Anisotropic 3D Mortar
15. Demont Léo, Mesnil Romain, Ducoulombier Nicolas, Caron Jean-François (2023-10)
    Affordable In-Line Structuration Measurements of Printable Mortar with a Pocket-Shear-Vane
16. Demont Léo, Charrier Malo, Margerit Pierre, Ducoulombier Nicolas et al. (2022-06)
    Flow-Based Pultrusion of Anisotropic Concrete:
    Mechanical Properties at Hardened State
17. Roussel Nicolas, Buswell Richard, Ducoulombier Nicolas, Ivanova Irina et al. (2022-06)
    Assessing the Fresh Properties of Printable Cement-Based Materials:
    High-Potential Tests for Quality-Control
18. Kuzmenko Kateryna, Ducoulombier Nicolas, Féraille Adélaïde, Roussel Nicolas (2022-05)
    Environmental Impact of Extrusion-Based Additive Manufacturing:
    Generic Model, Power-Measurements and Influence of Printing-Resolution
19. Caron Jean-François, Demont Léo, Ducoulombier Nicolas, Mesnil Romain (2021-06)
    3D Printing of Mortar with Continuous Fibers:
    Principle, Properties and Potential for Application
20. Ducoulombier Nicolas, Mesnil Romain, Carneau Paul, Demont Léo et al. (2021-05)
    The “Slugs-Test” for Extrusion-Based Additive Manufacturing:
    Protocol, Analysis and Practical Limits
21. Demont Léo, Ducoulombier Nicolas, Mesnil Romain, Caron Jean-François (2021-01)
    Flow-Based Pultrusion of Continuous Fibers for Cement-Based Composite Material and Additive Manufacturing:
    Rheological and Technological Requirements
22. Carneau Paul, Mesnil Romain, Ducoulombier Nicolas, Roussel Nicolas et al. (2020-07)
    Characterisation of the Layer-Pressing-Strategy for Concrete 3D Printing
23. Duballet Romain, Mesnil Romain, Ducoulombier Nicolas, Carneau Paul et al. (2020-07)
    Free Deposition-Printing for Space-Truss-Structures
24. Ducoulombier Nicolas, Carneau Paul, Mesnil Romain, Demont Léo et al. (2020-07)
    The Slug-Test:
    In-Line-Assessment of Yield-Stress for Extrusion-Based Additive Manufacturing
25. Ducoulombier Nicolas, Demont Léo, Chateau Camille, Bornert Michel et al. (2020-04)
    Additive Manufacturing of Anisotropic Concrete:
    A Flow-Based Pultrusion of Continuous Fibers in a Cementitious Matrix
26. Ducoulombier Nicolas (2019-06)
    Characterisation and Modelling of Interfacial-Damage in Fiber-Reinforced Concrete for 3D Printing in Construction