Research-Progress of Concrete 3D Printing Technology and Its Equipment System, Material, and Molding-Defect-Control (2022-09)¶
, Meng Wei, Wang Peifu, Qian Dongqing, Cheng Wei, Jia Zhongqing
Journal Article - Journal of Engineering, Vol. 2022, pp. 1-22
Abstract
The traditional construction technology not only has environmental friendly problems such as noise and dust but also has resource-saving problems such as large template quantity and low construction accuracy. In addition, the traditional construction technology has an insurmountable technical bottleneck in the construction of special-shaped buildings. Building 3D printing technology can effectively overcome many problems existing in traditional construction technology and provide unlimited possibilities for the construction of special-shaped buildings. Concrete 3D printing technology is one of the most important technical categories of building 3D printing. In this study, the research status and progress of concrete 3D technology were reviewed from the aspects of equipment system, materials, defect control, and application scenarios. On this basis, the development foreground was prospected.
¶
33 References
- Álvarez-Fernández Martina, Prendes-Gero María, González-Nicieza Celestino, Guerrero-Miguel Diego-José et al. (2021-02)
Optimum Mix-Design for 3D Concrete Printing Using Mining-Tailings:
A Case Study in Spain - Arunothayan Arun, Nematollahi Behzad, Ranade Ravi, Bong Shin et al. (2021-02)
Fiber-Orientation Effects on Ultra-High-Performance Concrete Formed by 3D Printing - Bosscher Paul, Williams Robert, Bryson L., Castro-Lacouture Daniel (2007-04)
Cable-Suspended Robotic Contour Crafting System - Chu Shaohua, Li Leo, Kwan Albert (2020-09)
Development of Extrudable High-Strength Fiber-Reinforced Concrete Incorporating Nano-Calcium-Carbonate - Craveiro Flávio, Nazarian Shadi, Bártolo Helena, Bartolo Paulo et al. (2020-02)
An Automated System for 3D Printing Functionally Graded Concrete-Based Materials - Ding Tao, Xiao Jianzhuang, Zou Shuai, Zhou Xinji (2020-08)
Anisotropic Behavior in Bending of 3D Printed Concrete Reinforced with Fibers - Helm Volker, Willmann Jan, Gramazio Fabio, Kohler Matthias (2013-11)
In-Situ Robotic Fabrication:
Advanced Digital Manufacturing Beyond the Laboratory - Hoffmann Marcin, Skibicki Szymon, Pankratow Paweł, Zieliński Adam et al. (2020-04)
Automation in the Construction of a 3D Printed Concrete Wall with the Use of a Lintel Gripper - Kaszyńska Maria, Skibicki Szymon, Hoffmann Marcin (2020-12)
3D Concrete Printing for Sustainable Construction - Khalil Abdullah, Wang Xiangyu, Celik Kemal (2020-02)
3D Printable Magnesium Oxide Concrete:
Towards Sustainable Modern Architecture - Khan Mohd (2020-04)
Mix Suitable for Concrete 3D Printing:
A Review - Kloft Harald, Krauss Hans-Werner, Hack Norman, Herrmann Eric et al. (2020-05)
Influence of Process Parameters on the Inter-Layer Bond Strength of Concrete Elements Additive Manufactured by Shotcrete 3D Printing - Lao Wenxin, Li Mingyang, Tjahjowidodo Tegoeh (2020-09)
Variable-Geometry Nozzle for Surface Quality Enhancement in 3D Concrete Printing - Le Thanh, Austin Simon, Lim Sungwoo, Buswell Richard et al. (2012-01)
Mix-Design and Fresh Properties for High-Performance Printing Concrete - Li Zhijian, Wang Li, Ma Guowei (2018-05)
Method for the Enhancement of Buildability and Bending-Resistance of 3D Printable Tailing Mortar - Li Zhijian, Wang Li, Ma Guowei, Sanjayan Jay et al. (2020-07)
Strength and Ductility Enhancement of 3D Printing Structure Reinforced by Embedding Continuous Micro-Cables - Li Leo, Xiao Bofeng, Fang Z., Xiong Z. et al. (2020-11)
Feasibility of Glass-Basalt Fiber-Reinforced Seawater Coral Sand Mortar for 3D Printing - Lim Jian, Weng Yiwei, Pham Quang-Cuong (2019-10)
3D Printing of Curved Concrete Surfaces Using Adaptable Membrane Formwork - Moelich Gerrit, Kruger Jacques, Combrinck Riaan (2020-08)
Plastic Shrinkage Cracking in 3D Printed Concrete - Nguyen Vuong, Panda Biranchi, Zhang Guomin, Nguyen-Xuan Hung et al. (2021-01)
Digital Design Computing and Modelling for 3D Concrete Printing - Pan Tinghong, Jiang Yaqing, He Hui, Wang Yu et al. (2021-01)
Effect of Structural Build-Up on Inter-Layer Bond Strength of 3D Printed Cement Mortars - Pegna Joseph (1997-02)
Exploratory Investigation of Solid Freeform Construction - Sakka Fatima, Assaad Joseph, Hamzeh Farook, Nakhoul Charbel (2019-07)
Thixotropy and Interfacial Bond Strengths of Polymer-Modified Printed Mortars - Salet Theo, Ahmed Zeeshan, Bos Freek, Laagland Hans (2018-05)
Design of a 3D Printed Concrete Bridge by Testing - Shahzad Qamar, Wang Xujiang, Wang Wenlong, Wan Yi et al. (2020-06)
Coordinated Adjustment and Optimization of Setting-Time, Flowability, and Mechanical Strength for Construction 3D Printing Material Derived from Solid Waste - Souza Marcelo, Ferreira Igor, Moraes Elisângela, Senff Luciano et al. (2020-09)
3D Printed Concrete for Large-Scale Buildings:
An Overview of Rheology, Printing Parameters, Chemical Admixtures, Reinforcements, and Economic and Environmental Prospects - Tho Tuong, Thinh Nguyen (2021-01)
Using a Cable-Driven Parallel Robot with Applications in 3D Concrete Printing - Xiao Jianzhuang, Zou Shuai, Yu Ying, Wang Yu et al. (2020-09)
3D Recycled Mortar Printing:
System-Development, Process-Design, Material-Properties and On-Site-Printing - Xu Weiguo, Gao Yuan, Sun Chenwei, Wang Zhi (2020-09)
Fabrication and Application of 3D Printed Concrete Structural Components in the Boshan Pedestrian Bridge Project - Ye Junhong, Cui Can, Yu Jiangtao, Yu Kequan et al. (2021-01)
Fresh and Anisotropic-Mechanical Properties of 3D Printable Ultra-High-Ductile Concrete with Crumb-Rubber - Yu Shiwei, Du Hongjian, Sanjayan Jay (2020-07)
Aggregate-Bed 3D Concrete Printing with Cement-Paste Binder - Yu Kequan, McGee Wesley, Ng Tsz, Zhu He et al. (2021-02)
3D Printable Engineered Cementitious Composites:
Fresh and Hardened Properties - Zareiyan Babak, Khoshnevis Behrokh (2018-04)
_Effects of Mixture Ingredients on Inter-Layer Adhesion of Concrete in Contour Crafting
9 Citations
- Benz Hendrik, Nguyen Trong The, Klemt-Albert Katharina (2025-11)
Real-Time Vision-Based Defect Detection for Large-Scale on-Site Earthen Additive Manufacturing:
Annotated Dataset and Dual-Model Framework - Liu Han, Sousa Israel, Laflamme Simon, Doyle Shelby et al. (2025-09)
Embedment of 3D Printed Self-Sensing Composites for Smart Cementitious Components - Li Nan, Deng Yongjie, Li Weihong, Li Lingyu et al. (2025-08)
Performance of Active-Magnesia-Based Magnesium Phosphate Cement and Application of Rapid-Solidification 3D Printing Technology - Sangiorgio Valentino, Bianchi Iacopo, Forcellese Archimede (2025-02)
Advancing Decarbonization Through 3D Printed Concrete Formworks:
LIFE Cycle Analysis of Technologies, Materials, and Processes - Chourasia Ajay, Pal Biswajit, Kapoor Ashish (2025-02)
Influence of Printing Direction and Interlayer Printing Time on the Bond Characteristics and Hardened Mechanical Properties of Agro-Industrial Waste-Based 3D Printed Concrete - Hassan Amer, Alomayri Thamer, Noaman Mohammed, Zhang Chunwei (2025-01)
3D Printed Concrete for Sustainable Construction:
A Review of Mechanical Properties and Environmental Impact - Arif Muhammad, Jan Faizullah, Rezzoug Aïssa, Afridi Muhammad et al. (2024-11)
Data-Driven Models for Predicting Compressive Strength of 3D Printed Fiber-Reinforced Concrete Using Interpretable Machine Learning Algorithms - Alencar Oliveira Francisco, Picelli Sanches Renato, Barari Ahmad, Oliveira Romano Roberto et al. (2024-09)
Greenhouse Gases Emission Reduction Trough Topology-Optimization and 3D Printing - Zhao Shun, Wang Qiang, Fang Xinjun, Liang Wei et al. (2022-12)
Application and Development of Autonomous Robots in Concrete Construction:
Challenges and Opportunities
BibTeX
@article{zhao_meng_wang_qian.2022.RPoC3PTaIESMaMDC,
author = "Yanhua Zhao and Wei Meng and Peifu Wang and Dongqing Qian and Wei Cheng and Zhongqing Jia",
title = "Research-Progress of Concrete 3D Printing Technology and Its Equipment System, Material, and Molding-Defect-Control",
doi = "10.1155/2022/6882386",
year = "2022",
journal = "Journal of Engineering",
volume = "2022",
pages = "1--22",
}
Formatted Citation
Y. Zhao, W. Meng, P. Wang, D. Qian, W. Cheng and Z. Jia, “Research-Progress of Concrete 3D Printing Technology and Its Equipment System, Material, and Molding-Defect-Control”, Journal of Engineering, vol. 2022, pp. 1–22, 2022, doi: 10.1155/2022/6882386.
Zhao, Yanhua, Wei Meng, Peifu Wang, Dongqing Qian, Wei Cheng, and Zhongqing Jia. “Research-Progress of Concrete 3D Printing Technology and Its Equipment System, Material, and Molding-Defect-Control”. Journal of Engineering 2022 (2022): 1–22. https://doi.org/10.1155/2022/6882386.