Review of Binder-Jetting 3D Printing in the Construction Industry (2022-01)¶
, , ,
Journal Article - Progress in Additive Manufacturing, Vol. None, Iss. None
Abstract
Binder jetting (inkjet), featured by the dripping of liquid on the powder-based layer for solidification and bonding, is the second most popular 3D printing (3DP) technology for the construction industry. Therefore, an overview of this technology is necessary for both industry and academia. The paper discussed the most suitable materials for the construction industry which can be used in binder jetting 3DP. Attention was given not only to the selection of the materials but also the printing process and challenges that might face the printing process and post-processing stages, with an emphasis on sustainability and suitability. The whole process of printing gypsum, cement and geopolymer mortar, clay, chipped wood and sand materials through the binder jetting technique has been summarized, followed by curing and post-processing to achieve desirable mechanical properties. Finally, an informative approach was introduced for the scale-up of binder jetting 3DP in the construction industry.
¶
21 References
- Chu Shaohua, Li Leo, Kwan Albert (2020-09)
Development of Extrudable High-Strength Fiber-Reinforced Concrete Incorporating Nano-Calcium-Carbonate - Hack Norman, Mai (née Dressler) Inka, Brohmann Leon, Gantner Stefan et al. (2020-03)
Injection 3D Concrete Printing (I3DCP):
Basic Principles and Case Studies - Ingaglio Joseph, Fox John, Naito Clay, Bocchini Paolo (2019-02)
Material-Characteristics of Binder-Jet 3D Printed Hydrated CSA Cement with the Addition of Fine Aggregates - Kontovourkis Odysseas, Tryfonos George (2019-11)
Robotic 3D Clay Printing of Prefabricated Non-Conventional Wall Components Based on a Parametric-Integrated Design - Lowke Dirk, Dini Enrico, Perrot Arnaud, Weger Daniel et al. (2018-07)
Particle-Bed 3D Printing in Concrete Construction:
Possibilities and Challenges - Lowke Dirk, Talke Daniel, Mai (née Dressler) Inka, Weger Daniel et al. (2020-05)
Particle-Bed 3D Printing by Selective Cement-Activation:
Applications, Material and Process Technology - Panda Biranchi, Ruan Shaoqin, Unluer Cise, Tan Ming (2018-11)
Improving the 3D Printability of High-Volume Fly-Ash Mixtures via the Use of Nano-Attapulgite-Clay - Panda Biranchi, Ruan Shaoqin, Unluer Cise, Tan Ming (2020-01)
Investigation of the Properties of Alkali-Activated Slag Mixes Involving the Use of Nano-Clay and Nucleation-Seeds for 3D Printing - Panda Biranchi, Tay Yi, Paul Suvash, Tan Ming (2018-05)
Current Challenges and Future Potential of 3D Concrete Printing - Paolini Alexander, Kollmannsberger Stefan, Rank Ernst (2019-10)
Additive Manufacturing in Construction:
A Review on Processes, Applications, and Digital Planning Methods - Pegna Joseph (1997-02)
Exploratory Investigation of Solid Freeform Construction - Salman Nazar, Ma Guowei, Ijaz Nauman, Wang Li (2021-04)
Importance and Potential of Cellulosic Materials and Derivatives in Extrusion-Based 3D Concrete Printing:
Prospects and Challenges - Sepasgozar Samad, Shi Anqi, Yang Liming, Shirowzhan Sara et al. (2020-12)
Additive Manufacturing Applications for Industry 4.0:
A Systematic Critical Review - Shakor Pshtiwan, Gowripalan Nadarajah, Rasouli Habib (2021-03)
Experimental and Numerical Analysis of 3D Printed Cement Mortar Specimens Using Inkjet 3DP - Shakor Pshtiwan, Nejadi Shami, Gowripalan Nadarajah (2020-07)
Effect of Heat-Curing and E6-Glass Fiber-Reinforcement Addition on Powder-Based 3DP Cement Mortar - Shakor Pshtiwan, Nejadi Shami, Paul Gavin (2019-11)
Investigation into the Effect of Delays Between Printed Layers on the Mechanical Strength of Inkjet 3DP Mortar - Shakor Pshtiwan, Nejadi Shami, Paul Gavin, Malek Sardar (2019-01)
Review of Emerging Additive Manufacturing Technologies in 3D Printing of Cementitious Materials in the Construction Industry - Shakor Pshtiwan, Nejadi Shami, Paul Gavin, Sanjayan Jay (2019-12)
Dimensional Accuracy, Flowability, Wettability, and Porosity in Inkjet 3DP for Gypsum and Cement Mortar Materials - Shakor Pshtiwan, Sanjayan Jay, Nazari Ali, Nejadi Shami (2017-02)
Modified 3D Printed Powder to Cement-Based Material and Mechanical Properties of Cement Scaffold Used in 3D Printing - Teizer Jochen, Blickle Alexander, King Tobias, Leitzbach Olaf et al. (2016-07)
Large-Scale 3D Printing of Complex Geometric Shapes in Construction - Wi Kwangwoo, Suresh Vignesh, Wang Kejin, Li Beiwen et al. (2019-12)
Quantifying Quality of 3D Printed Clay Objects Using a 3D Structured Light Scanning System
20 Citations
- Flor-Unda Omar, Toapanta Carlos, Fuentes Mauricio, Rivera Mario (2025-07)
Additive Manufacturing Technologies:
Advances for the Construction Industry - Tang Boyang, Yan Jiachuan, Han Xiaoyu, Lin Yini et al. (2025-05)
Mechanical Properties of Extrusion-Based 3D-Printed Concrete Considering the Thickness of the Printed Layer and Printing Time Interval - Becher Anton, Gądek Szymon, Korniejenko Kinga (2025-05)
3D Printing with Geopolymers and Its Applications - Oladunni Oluwole, Lee Carman, Ibrahim Idowu, Olanrewaju Oludolapo (2025-03)
Advances in Sustainable Additive Manufacturing:
A Systematic Review for Construction Industry to Mitigate Greenhouse Gas Emissions - Nadi Mouad, Majdoubi Hicham, Haddaji Younesse, Bili Oumaima et al. (2025-01)
Digital Fabrication Processes for Cementitious Materials Using Three-Dimensional 3D Printing Technologies - Liu Junxing, Li Peiqi, Piao Taiyan, Im Sumin et al. (2024-12)
High-Alumina Cementitious Materials for Binder-Jetting 3D Printing:
Exploring Suitable Mixing-Ratio and Curing-Solution for Improving Mechanical Properties and Hydration-Reaction - Jin Peng, Hasany Masoud, Kohestanian Mohammad, Mehrali Mehdi (2024-10)
Micro/Nano Additives in 3D Printing Concrete:
Opportunities, Challenges, and Potential Outlook in Construction Applications - Parrott Brian, Coronado Preciado Angelica, Feron Eric (2024-07)
Selective Sheet-Extrusion:
A Novel Manufacturing-Process for Large-Format Material-Extrusion - Krishna R., Rehman Asif, Mishra Jyotirmoy, Saha Suman et al. (2024-06)
Additive Manufacturing of Geopolymer Composites for Sustainable Construction:
Critical Factors, Advancements, Challenges, and Future Directions - Salari Farid, Zocca Andrea, Bosetti Paolo, Hlaváček Petr et al. (2024-05)
Powder-Bed 3D Printing by Selective Activation of Magnesium-Phosphate-Cement:
Determining Significant Processing Parameters and Their Effect on Mechanical Strength - Hassan Habibelrahman, Rodriguez-Ubinas Edwin, Tamimi Adil, Trepci Esra et al. (2024-04)
Towards Innovative and Sustainable Buildings:
A Comprehensive Review of 3D Printing in Construction - Tiwari Adarsh, Pratapa Phanisri, Santhanam Manu (2024-03)
Lattice Concrete:
3D Printed Periodic Cellular Structures Through Selective Cement-Hydration - Liu Xiongfei, Wang Nan, Zhang Yi, Ma Guowei (2024-02)
Optimization of Printing Precision and Mechanical Property for Powder-Based 3D Printed Magnesium Phosphate Cement Using Fly-Ash - Wang Xingjian, Naito Clay, Fox John, Bocchini Paolo (2024-02)
Impact of Mix Proportions on Particle-Bed 3D Printed Concrete Properties - Kakarla Akesh, Kong Ing, Patel Vipulkumar (2024-02)
Additive Manufacturing for Building and Constructions - Panda Biranchi, Shakor Pshtiwan, Laghi Vittoria (2023-12)
Powder-Bed Additive Manufacturing - Panda Biranchi, Shakor Pshtiwan, Laghi Vittoria (2023-12)
Shotcrete Additive Manufacturing - Ma Xiaosong, Tan Linzhen, Lu Yuanjing, Yao Wu et al. (2023-03)
Upcycling of Waste Plasterboard for the Synthesis of High-Quality Gypsum-Based 3D Printing-Powder - Korniejenko Kinga, Setlak (nee Pławecka) Kinga, Kozub Barbara (2022-12)
An Overview for Modern Energy-Efficient Solutions for Lunar and Martian Habitats Made Based on Geopolymers Composites and 3D Printing Technology - Puzatova (nee Sharanova) Anastasiia, Shakor Pshtiwan, Laghi Vittoria, Dmitrieva Maria (2022-11)
Large-Scale 3D Printing for Construction Application by Means of Robotic Arm and Gantry 3D Printer:
A Review
BibTeX
@article{shak_chu_puza_dini.2022.RoBJ3PitCI,
author = "Pshtiwan N. Shakor and Shaohua H. Chu and Anastasiia V. Puzatova (nee Sharanova) and Enrico Dini",
title = "Review of Binder-Jetting 3D Printing in the Construction Industry",
doi = "10.1007/s40964-021-00252-9",
year = "2022",
journal = "Progress in Additive Manufacturing",
volume = "None",
number = "None",
}
Formatted Citation
P. N. Shakor, S. H. Chu, A. V. P. (nee Sharanova) and E. Dini, “Review of Binder-Jetting 3D Printing in the Construction Industry”, Progress in Additive Manufacturing, vol. None, no. None, 2022, doi: 10.1007/s40964-021-00252-9.
Shakor, Pshtiwan N., Shaohua H. Chu, Anastasiia V. Puzatova (nee Sharanova), and Enrico Dini. “Review of Binder-Jetting 3D Printing in the Construction Industry”. Progress in Additive Manufacturing None, no. None (2022). https://doi.org/10.1007/s40964-021-00252-9.