Fresh and Hardened Properties of 3D Printing Mortar Modified by Halloysite-Nanotube (2024-06)¶
, , ,
Journal Article - Journal of Building Engineering, No. 109828
Abstract
This study presents the impacts of different dosages of halloysite nanotube (HNT) on the characteristics of 3D printing mortar (3DPM). The fresh behavior of 3DPM alongside with its hardened performance and microstructural characteristics were evaluated. Results indicated that HNT accelerates the setting time of 3DPM. 3% of HNT (HNT3) increased the yield stress and thixotropy of 3DPM by around 537 and 248%, respectively. The improvement in green strength (265%) and shape stability (69%) of 3%-HNT-modified 3DPM samples was observed. HNT3 also enhanced the flexural (45%), compressive (39%), and interlayer-bond (19%) strengths. Furthermore, durability-related characteristics results demonstrated that HNT3 can reduce sorptivity and gas porosity by approximately 42 and 55%, respectively, while it increases its electrical resistivity by about 48%. Outcomes obtained from microstructural analysis confirmed the denser microstructure of HNT-modified 3DPM. Therefore, HNT can be introduced as a promising candidate to improve both fresh and hardened characteristics of 3DPM.
¶
30 References
- Alhumayani Hashem, Gomaa Mohamed, Soebarto Veronica, Jabi Wassim (2020-06)
Environmental Assessment of Large-Scale 3D Printing in Construction:
A Comparative Study between Cob and Concrete - Batikha Mustafa, Jotangia Rahul, Baaj Mohamad, Mousleh Ibrahim (2021-12)
3D Concrete Printing for Sustainable and Economical Construction:
A Comparative Study - Chougan Mehdi, Ghaffar Seyed, Jahanzat Mohammad, Albar Abdulrahman et al. (2020-04)
The Influence of Nano-Additives in Strengthening Mechanical Performance of 3D Printed Multi-Binder Geopolymer Composites - Chougan Mehdi, Ghaffar Seyed, Sikora Paweł, Chung Sang-Yeop et al. (2021-02)
Investigation of Additive Incorporation on Rheological, Microstructural and Mechanical Properties of 3D Printable Alkali-Activated Materials - Chu Shaohua, Li Leo, Kwan Albert (2020-09)
Development of Extrudable High-Strength Fiber-Reinforced Concrete Incorporating Nano-Calcium-Carbonate - Ding Tao, Xiao Jianzhuang, Qin Fei, Duan Zhenhua (2020-03)
Mechanical Behavior of 3D Printed Mortar with Recycled Sand at Early-Ages - Holt Camille, Edwards Laurie, Keyte Louise, Moghaddam Farzad et al. (2019-02)
Construction 3D Printing - Hou Shaodan, Duan Zhenhua, Xiao Jianzhuang, Ye Jun (2020-12)
A Review of 3D Printed Concrete:
Performance-Requirements, Testing Measurements and Mix-Design - Jayathilakage Roshan, Rajeev Pathmanathan, Sanjayan Jay (2020-01)
Yield-Stress-Criteria to Assess the Buildability of 3D Concrete Printing - Kazemian Ali, Yuan Xiao, Cochran Evan, Khoshnevis Behrokh (2017-04)
Cementitious Materials for Construction-Scale 3D Printing:
Laboratory Testing of Fresh Printing Mixture - Khoshnevis Behrokh (2003-11)
Automated Construction by Contour Crafting:
Related Robotics and Information Technologies - Lee Hojae, Kim Jang-Ho, Moon Jae-Heum, Kim Won-Woo et al. (2019-08)
Correlation Between Pore Characteristics and Tensile Bond Strength of Additive Manufactured Mortar Using X-Ray Computed Tomography - Liu Zhenbang, Li Mingyang, Moo Guo, Kobayashi Hitoshi et al. (2023-05)
Effect of Nano-Structured Silica-Additives on the Extrusion-Based 3D Concrete Printing Application - Marchment Taylor, Sanjayan Jay, Nematollahi Behzad, Xia Ming (2019-02)
Inter-Layer Strength of 3D Printed Concrete - Marchment Taylor, Sanjayan Jay, Xia Ming (2019-03)
Method of Enhancing Inter-Layer Bond Strength in Construction-Scale 3D Printing with Mortar by Effective Bond Area Amplification - Nerella Venkatesh, Krause Martin, Mechtcherine Viktor (2019-11)
Direct Printing-Test for Buildability of 3D Printable Concrete Considering Economic Viability - Panda Biranchi, Lim Jian, Tan Ming (2019-02)
Mechanical Properties and Deformation Behavior of Early-Age Concrete in the Context of Digital Construction - Putten Jolien, Deprez Maxim, Cnudde Veerle, Schutter Geert et al. (2019-09)
Microstructural Characterization of 3D Printed Cementitious Materials - Razzaghian Ghadikolaee Mehrdad, Cerro-Prada Elena, Pan Zhu, Korayem Asghar (2023-04)
Nanomaterials as Promising Additives for High-Performance 3D Printed Concrete:
A Critical Review - Şahin Hatice, Mardani Ali (2021-12)
Assessment of Materials, Design Parameters and Some Properties of 3D Printing Concrete Mixtures:
A State of the Art Review - Sanjayan Jay, Jayathilakage Roshan, Rajeev Pathmanathan (2020-11)
Vibration-Induced Active Rheology-Control for 3D Concrete Printing - Sanjayan Jay, Nematollahi Behzad, Xia Ming, Marchment Taylor (2018-04)
Effect of Surface Moisture on Inter-Layer Strength of 3D Printed Concrete - Sanjayan Jay, Nematollahi Behzad, Xia Ming, Marchment Taylor (2021-06)
Effect of Surface Moisture on Inter-Layer Strength of 3D Printed Concrete:
Correction - Sikora Paweł, Chung Sang-Yeop, Liard Maxime, Lootens Didier et al. (2021-02)
The Effects of Nano-Silica on the Fresh and Hardened Properties of 3D Printable Mortars - Skibicki Szymon, Szewczyk Piotr, Majewska Julia, Sibera Daniel et al. (2024-03)
The Effect of Inter-Layer Adhesion on Stress-Distribution in 3D Printed Beam Elements - Weng Yiwei, Li Mingyang, Ruan Shaoqin, Wong Teck et al. (2020-03)
Comparative Economic, Environmental and Productivity-Assessment of a Concrete Bathroom Unit Fabricated Through 3D Printing and a Pre-Cast Approach - Wu Yiwen, Liu Chao, Liu Huawei, Zhang Zhenzi et al. (2021-07)
Study on the Rheology and Buildability of 3D Printed Concrete with Recycled Coarse Aggregates - Xu Ping, Chen Tianyu, Fan Kaijun, Zhang Minxia (2023-11)
Effect of Nano-Silica-Sol Dosage on the Properties of 3D Printed Concrete - Zhang Yu, Zhang Yunsheng, Liu Guojian, Yang Yonggan et al. (2018-04)
Fresh Properties of a Novel 3D Printing Concrete Ink - Zhang Yu, Zhang Yunsheng, She Wei, Yang Lin et al. (2019-01)
Rheological and Hardened Properties of the High-Thixotropy 3D Printing Concrete
2 Citations
- Nan Bo, Qiao Youxin, Leng Junjie, Bai Yikui (2025-01)
Advancing Structural Reinforcement in 3D Printed Concrete:
Current Methods, Challenges, and Innovations - Jin Peng, Hasany Masoud, Kohestanian Mohammad, Mehrali Mehdi (2024-10)
Micro/Nano Additives in 3D Printing Concrete:
Opportunities, Challenges, and Potential Outlook in Construction Applications
BibTeX
@article{razz_pan_cerr_kora.2024.FaHPo3PMMbHN,
author = "Mehrdad Razzaghian Ghadikolaee and Zhu Pan and Elena Cerro-Prada and Asghar Habibnejad Korayem",
title = "Fresh and Hardened Properties of 3D Printing Mortar Modified by Halloysite-Nanotube",
doi = "10.1016/j.jobe.2024.109828",
year = "2024",
journal = "Journal of Building Engineering",
pages = "109828",
}
Formatted Citation
M. R. Ghadikolaee, Z. Pan, E. Cerro-Prada and A. H. Korayem, “Fresh and Hardened Properties of 3D Printing Mortar Modified by Halloysite-Nanotube”, Journal of Building Engineering, p. 109828, 2024, doi: 10.1016/j.jobe.2024.109828.
Ghadikolaee, Mehrdad Razzaghian, Zhu Pan, Elena Cerro-Prada, and Asghar Habibnejad Korayem. “Fresh and Hardened Properties of 3D Printing Mortar Modified by Halloysite-Nanotube”. Journal of Building Engineering, 2024, 109828. https://doi.org/10.1016/j.jobe.2024.109828.