Skip to content

Additive Manufacturing of Sustainable Construction Materials and Form-Finding Structures (2022-02)

A Review on Recent Progresses

10.1089/3dp.2020.0331

 Liu Junli,  van Nguyen Vuong,  Panda Biranchi,  Fox Kate,  du Plessis Anton,  Tran Jonathan
Journal Article - 3D Printing and Additive Manufacturing, Vol. 9, Iss. 1, pp. 12-34

Abstract

Recently, there has been an increasing interest on the sustainability advantage of 3D concrete printing (3DCP), where the original cement-based mixtures used for printing could be replaced or incorporated with environmental-friendly materials. The development in digital modeling and design tools also creates a new realm of form-finding architecture for 3DCP, which is based on topological optimization of volumetric mass and physical performance. This review provides a perspective of using different green cementitious materials, applications of structural optimization, and modularization methods for realizing sustainable construction with additive manufacturing. The fresh and hardened mechanical properties of various sustainable materials for extrusion-based 3D printing are presented, followed by discussions on different topology optimization techniques. The current state of global research and industrial applications in 3DCP, along with the development of sustainable construction materials, is also summarized. Finally, research and practical gaps identified in this review lead to several recommendations on material developments, digital design tool's prospects for 3DCP to achieve the sustainability goal.

78 References

  1. Alghamdi Hussam, Nair Sooraj, Neithalath Narayanan (2019-02)
    Insights into Material-Design, Extrusion Rheology, and Properties of 3D Printable Alkali-Activated Fly-Ash-Based Binders
  2. Al-Qutaifi Sarah, Nazari Ali, Bagheri Ali (2018-07)
    Mechanical Properties of Layered Geopolymer Structures Applicable in Concrete 3D Printing
  3. Beigh Mirza, Nerella Venkatesh, Schröfl Christof, Mechtcherine Viktor (2015-06)
    Studying the Rheological Behavior of Limestone-Calcined-Clay-Cement (LC3) Mixtures in the Context of Extrusion-Based 3D Printing
  4. Bong Shin, Nematollahi Behzad, Nazari Ali, Xia Ming et al. (2018-09)
    Fresh and Hardened Properties of 3D Printable Geopolymer Cured in Ambient Temperature
  5. Bong Shin, Nematollahi Behzad, Nazari Ali, Xia Ming et al. (2019-03)
    Method of Optimization for Ambient Temperature Cured Sustainable Geopolymers for 3D Printing Construction Applications
  6. Bos Freek, Bosco Emanuela, Salet Theo (2018-11)
    Ductility of 3D Printed Concrete Reinforced with Short Straight Steel-Fibers
  7. Bos Freek, Wolfs Robert, Ahmed Zeeshan, Salet Theo (2016-08)
    Additive Manufacturing of Concrete in Construction:
    Potentials and Challenges of 3D Concrete Printing
  8. Buswell Richard, Silva Wilson, Jones Scott, Dirrenberger Justin (2018-06)
    3D Printing Using Concrete-Extrusion:
    A Roadmap for Research
  9. Chen Yu, Figueiredo Stefan, Yalçınkaya Çağlar, Çopuroğlu Oğuzhan et al. (2019-04)
    The Effect of Viscosity-Modifying Admixture on the Extrudability of Limestone and Calcined-Clay-Based Cementitious Material for Extrusion-Based 3D Concrete Printing
  10. Chen Mingxu, Guo Xiangyang, Zheng Yan, Li Laibo et al. (2018-11)
    Effect of Tartaric Acid on the Printable, Rheological and Mechanical Properties of 3D Printing Sulphoaluminate Cement-Paste
  11. Chen Yu, Li Zhenming, Figueiredo Stefan, Çopuroğlu Oğuzhan et al. (2019-04)
    Limestone and Calcined-Clay-Based Sustainable Cementitious Materials for 3D Concrete Printing:
    A Fundamental Study of Extrudability and Early-Age Strength Development
  12. Chen Mingxu, Li Laibo, Wang Jiaao, Huang Yongbo et al. (2019-10)
    Rheological Parameters and Building Time of 3D Printing Sulphoaluminate-Cement-Paste Modified by Retarder and Diatomite
  13. Chen Mingxu, Liu Bo, Li Laibo, Cao Lidong et al. (2020-01)
    Rheological Parameters, Thixotropy and Creep of 3D Printed Calcium-Sulfoaluminate-Cement Composites Modified by Bentonite
  14. Craveiro Flávio, Bártolo Helena, Gale Andrew, Duarte José et al. (2017-07)
    A Design Tool for Resource-Efficient Fabrication of 3D Graded Structural Building Components Using Additive Manufacturing
  15. Delgado Camacho Daniel, Clayton Patricia, Brien William, Seepersad Carolyn et al. (2018-02)
    Applications of Additive Manufacturing in the Construction Industry:
    A Forward-Looking Review
  16. Ding Zhu, Wang Xiaodong, Sanjayan Jay, Zou Patrick et al. (2018-11)
    A Feasibility Study on HPMC-Improved Sulphoaluminate Cement for 3D Printing
  17. Duballet Romain, Baverel Olivier, Dirrenberger Justin (2017-08)
    Classification of Building Systems for Concrete 3D Printing
  18. Figueiredo Stefan, Rodríguez Claudia, Ahmed Zeeshan, Bos Derk et al. (2019-03)
    An Approach to Develop Printable Strain-Hardening Cementitious Composites
  19. Hamidi Fatemeh, Aslani Farhad (2019-05)
    Additive Manufacturing of Cementitious Composites:
    Materials, Methods, Potentials, and Challenge
  20. Han Yilong, Yang Zhihan, Ding Tao, Xiao Jianzhuang (2020-08)
    Environmental and Economic Assessment on 3D Printed Buildings with Recycled Concrete
  21. Heever Marchant, Bester Frederick, Kruger Jacques, Zijl Gideon (2019-09)
    Effect of Silicon-Carbide-Nano-Particles on 3D Printability of Cement-Based Materials
  22. Khan Mohammad, Sanchez Florence, Zhou Hongyu (2020-04)
    3D Printing of Concrete:
    Beyond Horizons
  23. Kontovourkis Odysseas, Tryfonos George (2019-11)
    Robotic 3D Clay Printing of Prefabricated Non-Conventional Wall Components Based on a Parametric-Integrated Design
  24. Lloret-Fritschi Ena, Wangler Timothy, Gebhard Lukas, Mata-Falcón Jaime et al. (2020-05)
    From Smart Dynamic Casting to a Growing Family of Digital Casting Systems
  25. Lu Bing, Weng Yiwei, Li Mingyang, Qian Ye et al. (2019-02)
    A Systematical Review of 3D Printable Cementitious Materials
  26. Ma Guowei, Salman Nazar, Wang Li, Wang Fang (2020-02)
    A Novel Additive Mortar Leveraging Internal Curing for Enhancing Inter-Layer Bonding of Cementitious Composite for 3D Printing
  27. Mai (née Dressler) Inka, Freund Niklas, Lowke Dirk (2020-01)
    The Effect of Accelerator Dosage on Fresh Concrete Properties and on Inter-Layer Strength in Shotcrete 3D Printing
  28. Martens Pascal, Mathot Maarten, Bos Freek, Coenders Jeroen (2017-06)
    Optimizing 3D Printed Concrete Structures Using Topology Optimization
  29. Mechtcherine Viktor, Bos Freek, Perrot Arnaud, Silva Wilson et al. (2020-03)
    Extrusion-Based Additive Manufacturing with Cement-Based Materials:
    Production Steps, Processes, and Their Underlying Physics
  30. Mechtcherine Viktor, Nerella Venkatesh, Will Frank, Näther Mathias et al. (2019-08)
    Large-Scale Digital Concrete Construction:
    CONPrint3D Concept for On-Site, Monolithic 3D Printing
  31. Menna Costantino, Mata-Falcón Jaime, Bos Freek, Vantyghem Gieljan et al. (2020-04)
    Opportunities and Challenges for Structural Engineering of Digitally Fabricated Concrete
  32. Moeini Mohammad, Hosseinpoor Masoud, Yahia Ammar (2020-05)
    Effectiveness of the Rheometric Methods to Evaluate the Build-Up of Cementitious Mortars Used for 3D Printing
  33. Mohammad Malek, Masad Eyad, Ghamdi Sami (2020-12)
    3D Concrete Printing Sustainability:
    A Comparative Life Cycle Assessment of Four Construction Method Scenarios
  34. Moini Mohamadreza, Olek Jan, Youngblood Jeffrey, Magee Bryan et al. (2018-08)
    Additive Manufacturing and Performance of Architectured Cement-Based Materials
  35. Muthukrishnan Shravan, Kua Harn, Yu Ling, Chung Jacky (2020-05)
    Fresh Properties of Cementitious Materials Containing Rice-Husk-Ash for Construction 3D Printing
  36. Nematollahi Behzad, Vijay Praful, Sanjayan Jay, Nazari Ali et al. (2018-11)
    Effect of Polypropylene Fiber Addition on Properties of Geopolymers Made by 3D Printing for Digital Construction
  37. Neudecker Stefan, Bruns Christopher, Gerbers Roman, Heyn Jakob et al. (2016-05)
    A New Robotic Spray Technology for Generative Manufacturing of Complex Concrete-Structures without Formwork
  38. Nguyen Vuong, Panda Biranchi, Zhang Guomin, Nguyen-Xuan Hung et al. (2021-01)
    Digital Design Computing and Modelling for 3D Concrete Printing
  39. Panda Biranchi, Bhagath Singh Gangapatnam, Unluer Cise, Tan Ming (2019-02)
    Synthesis and Characterization of One-Part Geopolymers for Extrusion-Based 3D Concrete Printing
  40. Panda Biranchi, Mohamed Nisar, Paul Suvash, Bhagath Singh Gangapatnam et al. (2019-07)
    The Effect of Material Fresh Properties and Process Parameters on Buildability and Inter-Layer Adhesion of 3D Printed Concrete
  41. Panda Biranchi, Paul Suvash, Lim Jian, Tay Yi et al. (2017-08)
    Additive Manufacturing of Geopolymer for Sustainable Built Environment
  42. Panda Biranchi, Paul Suvash, Mohamed Nisar, Tay Yi et al. (2017-09)
    Measurement of Tensile Bond Strength of 3D Printed Geopolymer Mortar
  43. Panda Biranchi, Paul Suvash, Tan Ming (2017-07)
    Anisotropic Mechanical Performance of 3D Printed Fiber-Reinforced Sustainable Construction-Material
  44. Panda Biranchi, Ruan Shaoqin, Unluer Cise, Tan Ming (2018-11)
    Improving the 3D Printability of High-Volume Fly-Ash Mixtures via the Use of Nano-Attapulgite-Clay
  45. Panda Biranchi, Ruan Shaoqin, Unluer Cise, Tan Ming (2020-01)
    Investigation of the Properties of Alkali-Activated Slag Mixes Involving the Use of Nano-Clay and Nucleation-Seeds for 3D Printing
  46. Panda Biranchi, Tan Ming (2018-03)
    Experimental Study on Mix Proportion and Fresh Properties of Fly-Ash-Based Geopolymer for 3D Concrete Printing
  47. Panda Biranchi, Tan Ming (2018-11)
    Rheological Behavior of High-Volume Fly-Ash Mixtures Containing Micro-Silica for Digital Construction Application
  48. Panda Biranchi, Unluer Cise, Tan Ming (2018-10)
    Investigation of the Rheology and Strength of Geopolymer Mixtures for Extrusion-Based 3D Printing
  49. Panda Biranchi, Unluer Cise, Tan Ming (2019-08)
    Extrusion and Rheology Characterization of Geopolymer Nanocomposites Used in 3D Printing
  50. Paul Suvash, Tay Yi, Panda Biranchi, Tan Ming (2017-08)
    Fresh and Hardened Properties of 3D Printable Cementitious Materials for Building and Construction
  51. Perkins Isaac, Skitmore Martin (2015-03)
    Three-Dimensional Printing in the Construction Industry:
    A Review
  52. Perrot Arnaud, Rangeard Damien, Courteille Eric (2018-04)
    3D Printing of Earth-Based Materials:
    Processing Aspects
  53. Pham Luong, Tran Jonathan, Sanjayan Jay (2020-04)
    Steel-Fiber-Reinforced 3D Printed Concrete:
    Influence of Fiber Sizes on Mechanical Performance
  54. Rahul Attupurathu, Santhanam Manu (2020-02)
    Evaluating the Printability of Concretes Containing Lightweight Coarse Aggregates
  55. Rahul Attupurathu, Santhanam Manu, Meena Hitesh, Ghani Zimam (2019-08)
    Mechanical Characterization of 3D Printable Concrete
  56. Salet Theo, Ahmed Zeeshan, Bos Freek, Laagland Hans (2018-05)
    Design of a 3D Printed Concrete Bridge by Testing
  57. Schutter Geert, Lesage Karel, Mechtcherine Viktor, Nerella Venkatesh et al. (2018-08)
    Vision of 3D Printing with Concrete:
    Technical, Economic and Environmental Potentials
  58. Sun Xiaoyan, Wang Qun, Wang Hailong, Chen Long (2020-03)
    Influence of Multi-Walled Nanotubes on the Fresh and Hardened Properties of a 3D Printing PVA Mortar Ink
  59. Tay Yi, Panda Biranchi, Paul Suvash, Mohamed Nisar et al. (2017-05)
    3D Printing Trends in Building and Construction Industry:
    A Review
  60. Tay Yi, Panda Biranchi, Ting Guan, Ahamed N. et al. (2020-10)
    3D Printing for Sustainable Construction
  61. Tay Yi, Qian Ye, Tan Ming (2019-05)
    Printability-Region for 3D Concrete Printing Using Slump- and Slump-Flow-Test
  62. Vantyghem Gieljan, Corte Wouter, Shakour Emad, Amir Oded (2020-01)
    3D Printing of a Post-Tensioned Concrete Girder Designed by Topology-Optimization
  63. Vantyghem Gieljan, Corte Wouter, Steeman Marijke, Boel Veerle (2019-07)
    Density-Based Topology-Optimization for 3D Printable Building Structures
  64. Vantyghem Gieljan, Steeman Marijke, Corte Wouter, Boel Veerle (2020-07)
    Design-Optimization for 3D Concrete Printing:
    Improving Structural and Thermal Performances
  65. Wang Li, Tian Zehao, Ma Guowei, Zhang Mo (2020-02)
    Inter-Layer Bonding Improvement of 3D Printed Concrete with Polymer-Modified Mortar:
    Experiments and Molecular Dynamics Studies
  66. Weng Yiwei, Li Mingyang, Ruan Shaoqin, Wong Teck et al. (2020-03)
    Comparative Economic, Environmental and Productivity-Assessment of a Concrete Bathroom Unit Fabricated Through 3D Printing and a Pre-Cast Approach
  67. Weng Yiwei, Li Mingyang, Tan Ming, Qian Shunzhi (2018-01)
    Design 3D Printing Cementitious Materials via Fuller-Thompson-Theory and Marson-Percy-Model
  68. Weng Yiwei, Lu Bing, Li Mingyang, Liu Zhixin et al. (2018-09)
    Empirical Models to Predict Rheological Properties of Fiber-Reinforced Cementitious Composites for 3D Printing
  69. Weng Yiwei, Ruan Shaoqin, Li Mingyang, Mo Liwu et al. (2019-06)
    Feasibility Study on Sustainable-Magnesium-Potassium-Phosphate Cement-Paste for 3D Printing
  70. Wolfs Robert, Bos Freek, Salet Theo (2019-03)
    Hardened Properties of 3D Printed Concrete:
    The Influence of Process Parameters on Inter-Layer Adhesion
  71. Wu Peng, Wang Jun, Wang Xiangyu (2016-04)
    A Critical Review of the Use of 3D Printing in the Construction Industry
  72. Xiao Jianzhuang, Ji Guangchao, Zhang Yamei, Ma Guowei et al. (2021-06)
    Large-Scale 3D Printing Concrete Technology:
    Current Status and Future Opportunities
  73. Xu Weiguo, Gao Yuan, Sun Chenwei, Wang Zhi (2020-09)
    Fabrication and Application of 3D Printed Concrete Structural Components in the Boshan Pedestrian Bridge Project
  74. Yuan Qiang, Zhou Dajun, Li Baiyun, Huang Hai et al. (2017-11)
    Effect of Mineral Admixtures on the Structural Build-Up of Cement-Paste
  75. Zhang Chao, Hou Zeyu, Chen Chun, Zhang Yamei et al. (2019-09)
    Design of 3D Printable Concrete Based on the Relationship Between Flowability of Cement-Paste and Optimum Aggregate-Content
  76. Zhang Jingchuan, Wang Jialiang, Dong Sufen, Yu Xun et al. (2019-07)
    A Review of the Current Progress and Application of 3D Printed Concrete
  77. Zhang Yu, Zhang Yunsheng, Liu Guojian, Yang Yonggan et al. (2018-04)
    Fresh Properties of a Novel 3D Printing Concrete Ink
  78. Zhu Binrong, Pan Jinlong, Nematollahi Behzad, Zhou Zhenxin et al. (2019-07)
    Development of 3D Printable Engineered Cementitious Composites with Ultra-High Tensile Ductility for Digital Construction

40 Citations

  1. Iqbal Imtiaz, Kasim Tala, Besklubova Svetlana, Inqiad Waleed et al. (2025-12)
    Exploring Knowledge Domains and Future Research Directions in 3D Printed Concrete:
    A Bibliometric and Systematic Review
  2. Anastassiou Richard, Alvarado Rodrigo, Wegertseder Martínez Paulina (2025-11)
    Towards Climatomorphism:
    A Generative Optimization Framework for Climate-Adaptive 3D-Printed Free-Form Housing
  3. Najm-Eddine Asmae, Abouelmajd Mohamed, Najm-Eddine Youssef, Erritali Ilham et al. (2025-11)
    Topological Optimization in 3D Concrete Printing Structures:
    A Review
  4. Masri Abdullah, Vazquez Elaine, Haddad Assed, Najjar Mohammed (2025-10)
    Life Cycle Costing in 3D Printing:
    A Literature Review
  5. Ngo Than, Li Shuai, Huynh Tien, Zhang Y. et al. (2025-10)
    3D Printable Hemp Concrete:
    Rheological, Mechanical, and Microstructural Properties
  6. Ma Wei, Chen Junjie, Dai Yuntong, Zhou Yaya et al. (2025-10)
    Mechanical Properties of 3D Printed Concrete Irregular Structural Formwork:
    Experimental Study and Finite Element Analysis
  7. Li Shuai, Corelli Jaide, Tran Jonathan, Fan Linhua (2025-09)
    3D Printable Cellulose Concrete:
    A Review and Pathway to Future Research
  8. Maurya Shubham, Kumar Vijay, Panda Biranchi, Borsaikia Arun et al. (2025-09)
    Inline Polymer Cable Reinforcement in 3D Concrete Printing with a Special Nozzle
  9. Flor-Unda Omar, Toapanta Carlos, Fuentes Mauricio, Rivera Mario (2025-07)
    Additive Manufacturing Technologies:
    Advances for the Construction Industry
  10. Li Shuai, Liu Junli, Cheng Chi-Tsun, Xuan Hung et al. (2025-06)
    Design and Performance of 3D Printed Bouligand Steel Fiber-Reinforced Cementitious Composite Curved Beams
  11. Hassan Amer, Alomayri Thamer, Noaman Mohammed, Zhang Chunwei (2025-01)
    3D Printed Concrete for Sustainable Construction:
    A Review of Mechanical Properties and Environmental Impact
  12. Li Shuai, Khieu Hai, Black Jay, Nguyen Hung-Xuan et al. (2024-12)
    Two-Scale 3D Printed Steel-Fiber-Reinforcements-Strategy for Concrete Structures
  13. Guan Jingyuan, Wang Li, Huang Yimiao, Ma Guowei (2024-12)
    3D Printed Concrete Composite Slabs Fabricated by Pre-Stressed Reinforced Permanent Formwork:
    Design, Manufacturing, and Performance
  14. Habibi Alireza, Buswell Richard, Osmani Mohamed, Aziminezhad Mohamadmahdi (2024-11)
    Sustainability Principles in 3D Concrete Printing:
    Analysing Trends, Classifying Strategies, and Future Directions
  15. Zhi Zhenzhen, Guo Yanfei, Qi Huahui, Tan Hongbo et al. (2024-11)
    Effect of Alkali-Metal-Sulfates on Hydration Properties of Alpha-Calcium-Sulfate-Hemihydrate for 3D Printing
  16. Adamtsevich Liubov, Pustovgar Andrey, Adamtsevich Aleksey (2024-10)
    Assessing the Prospects and Risks of Delivering Sustainable Urban Development Through 3D Concrete Printing Implementation
  17. Li Shuai, Lan Tian, Nguyen Hung-Xuan, Tran Jonathan (2024-10)
    Frontiers in Construction 3D Printing:
    Self-Monitoring, Multi-Robot, Drone-Assisted Processes
  18. Tran Nhi, Tran Mien, Tran Jonathan, Nguyen Anh et al. (2024-09)
    Eco-Friendly 3D Printed Concrete Using Steel-Slag-Aggregate:
    Buildability, Printability and Mechanical Properties
  19. Zhu Jinggao, Cervera Miguel, Ren Xiaodan (2024-06)
    Buildability of Complex 3D Printed Concrete Geometries Using Peridynamics
  20. Spencer Lawson, Genedy Moneeb, Strait James, Nair Sriramya et al. (2024-06)
    Concrete Gyroid:
    An Additive Manufacturing (AM) Method to 3D Print Gyroid Geometries with a Cementitious Material
  21. Liu Junli, Haikola Pirjo, Fox Kate, Tran Jonathan (2024-06)
    3D Printing of Cementitious Composites with Seashell-Particles:
    Mechanical and Microstructural Analysis
  22. Curth Alexander, Pearl Natalie, Castro-Salazar Angelica, Mueller Caitlin et al. (2024-03)
    3D Printing Earth:
    Local, Circular Material Processing, Fabrication Methods, and Life Cycle Assessment
  23. Nguyen Vuong, Tran Jonathan, Liu Junli, Tran Mien et al. (2024-02)
    Extended Finite Element Multi-Scale Modelling for Crack Propagation in 3D Printed Fiber-Reinforced Concrete
  24. Moini Mohamadreza (2024-01)
    Perspectives in Architected Infrastructure Materials
  25. Sahai Rajan, Bisht Ravindra, Malviya Nitesh, Kumar Shivam et al. (2024-01)
    Aspects of Waste-Material-Utilization and 3D Concrete Printer Development-Approach:
    A Review
  26. Dey Dhrutiman, Nguyen Vuong, Nguyen-Xuan Hung, Srinivas Dodda et al. (2023-12)
    Flexural Performance of 3D Printed Concrete Structure with Lattice-Infills
  27. Christ Julian, Leusnik Sander, Koss Holger (2023-10)
    Multi-Axial 3D Printing of Biopolymer-Based Concrete Composites in Construction
  28. Akman Arabella, Sadhu Ayan (2023-10)
    Recent Development of 3D Printing Technology in Construction Engineering
  29. Liu Junli, Tran Jonathan, Ginigaddara Thusitha, Mendis Priyan (2023-06)
    Exploration of Using Graphene Oxide for Strength Enhancement of 3D Printed Cementitious Mortar
  30. Liu Junli, Tran Jonathan, Nguyen Vuong, Gunasekara Chamila et al. (2023-06)
    3D Printing of Cementitious Mortar with Milled Recycled Carbon-Fibers:
    Influences of Filament Offset on Mechanical Properties
  31. Paul Suvash, Basit Md, Hasan Noor, Dey Dhrutiman et al. (2023-04)
    3D Printing of Geopolymer Mortar:
    Overview of the Effect of Mix-Design and Printing Parameters on the Strength
  32. Wang Ziyue, Chen Zixuan, Xiao Jianzhuang, Ding Tao (2023-03)
    Experimental Study on Interfacial Shear Behavior of 3D Printed Recycled Mortar
  33. Nguyen Vuong, Li Shuai, Liu Junli, Nguyen Kien et al. (2022-11)
    Modelling of 3D Concrete Printing Process:
    A Perspective on Material and Structural Simulations
  34. Li Shuai, Nguyen-Xuan Hung, Tran Jonathan (2022-11)
    Digital Design and Parametric Study of 3D Concrete Printing on Non-Planar Surfaces
  35. Nguyen Vuong, Liu Junli, Li Shuai, Zhang Guomin et al. (2022-10)
    Modelling of 3D Printed Bio-Inspired Bouligand Cementitious Structures Reinforced with Steel-Fibers
  36. Liu Junli, Tran Jonathan (2022-09)
    Experimental Study on 3D-Printed Cementitious Materials Containing Surface-Modified Recycled Crumb-Rubber
  37. Boddepalli Uday, Panda Biranchi, Gandhi Indu (2022-09)
    Rheology and Printability of Portland-Cement-Based Materials:
    A Review
  38. Liu Junli, Setunge Sujeeva, Tran Jonathan (2022-07)
    3D Concrete Printing with Cement-Coated Recycled Crumb Rubber:
    Compressive and Microstructural Properties
  39. Bi Minghao, Xia Lingwei, Tran Jonathan, Li Zhi et al. (2022-04)
    Continuous Contour-Zigzag Hybrid Tool-Path for Large-Format Additive Manufacturing
  40. Nguyen Vuong, Nguyen-Xuan Hung, Panda Biranchi, Tran Jonathan (2022-03)
    3D Concrete Printing Modelling of Thin-Walled Structures

BibTeX 
@article{liu_nguy_pand_fox.2022.AMoSCMaFFS,
  author            = "Junli Liu and Vuong van Nguyen and Biranchi Narayan Panda and Kate Fox and Anton du Plessis and Jonathan Phuong Tran",
  title             = "Additive Manufacturing of Sustainable Construction Materials and Form-Finding Structures: A Review on Recent Progresses",
  doi               = "10.1089/3dp.2020.0331",
  year              = "2022",
  journal           = "3D Printing and Additive Manufacturing",
  volume            = "9",
  number            = "1",
  pages             = "12--34",
}
Formatted Citation

J. Liu, V. van Nguyen, B. N. Panda, K. Fox, A. du Plessis and J. P. Tran, “Additive Manufacturing of Sustainable Construction Materials and Form-Finding Structures: A Review on Recent Progresses”, 3D Printing and Additive Manufacturing, vol. 9, no. 1, pp. 12–34, 2022, doi: 10.1089/3dp.2020.0331.

Liu, Junli, Vuong van Nguyen, Biranchi Narayan Panda, Kate Fox, Anton du Plessis, and Jonathan Phuong Tran. “Additive Manufacturing of Sustainable Construction Materials and Form-Finding Structures: A Review on Recent Progresses”. 3D Printing and Additive Manufacturing 9, no. 1 (2022): 12–34. https://doi.org/10.1089/3dp.2020.0331.