3D Printing Concrete with Recycled Coarse Aggregates (2022-09)¶
The Influence of Pore-Structure on Inter-Layer Adhesion
10.1016/j.cemconcomp.2022.104742
, , Wu Yiwen, Bai Guoliang, He Chunhui, Yao Yizhou, Zhang Rongfei, Wang Youqiang
Journal Article - Cement and Concrete Composites, Vol. 134
Abstract
Concrete digital fabrication technology has been rapidly emerging while facing sustainability issues due to the high cement proportion in printed materials, rendering an environmentally friendly material design containing coarse aggregates one way for the concrete 3D printing industry to achieve more sustainable development. Here, 3D printed concrete with recycled coarse aggregate (RCA) was prepared, and its interlayer bonding properties were investigated considering different RCA replacement ratios, interlayer time intervals and layer heights. The results showed that RCA and the printing time interval degraded the interlayer bond strength, whereas no clear correlation was found with the layer height. Although the incorporation of RCA significantly changed the interlayer bonding system and cracking pattern, the interlayer bond strength of 3D printed recycled coarse aggregate concrete was substantially higher than that of 3D printed mortar. Finally, focusing on the pore structure characteristics, the mechanism influencing the interlayer bond performance is discussed.
¶
36 References
- Bai Gang, Wang Li, Ma Guowei, Sanjayan Jay et al. (2021-03)
3D Printing Eco-Friendly Concrete Containing Under-Utilised and Waste Solids as Aggregates - Chen Yu, Figueiredo Stefan, Li Zhenming, Chang Ze et al. (2020-03)
Improving Printability of Limestone-Calcined-Clay-Based Cementitious Materials by Using Viscosity-Modifying Admixture - Chen Yu, He Shan, Zhang Yu, Wan Zhi et al. (2021-08)
3D Printing of Calcined-Clay-Limestone-Based Cementitious Materials - Chen Yidong, Zhang Yunsheng, Pang Bo, Liu Zhiyong et al. (2021-05)
Extrusion-Based 3D Printing Concrete with Coarse Aggregate:
Printability and Direction-Dependent Mechanical Performance - Ding Tao, Xiao Jianzhuang, Qin Fei, Duan Zhenhua (2020-03)
Mechanical Behavior of 3D Printed Mortar with Recycled Sand at Early-Ages - Ding Tao, Xiao Jianzhuang, Zou Shuai, Wang Yu (2020-06)
Hardened Properties of Layered 3D Printed Concrete with Recycled Sand - Flatt Robert, Wangler Timothy (2022-05)
On Sustainability and Digital Fabrication with Concrete - Geng Zifan, She Wei, Zuo Wenqiang, Lyu Kai et al. (2020-09)
Layer-Interface Properties in 3D Printed Concrete:
Dual Hierarchical Structure and Micromechanical Characterization - Ji Guangchao, Xiao Jianzhuang, Zhi Peng, Wu Yuching et al. (2022-02)
Effects of Extrusion-Parameters on Properties of 3D Printing Concrete with Coarse Aggregates - Kloft Harald, Krauss Hans-Werner, Hack Norman, Herrmann Eric et al. (2020-05)
Influence of Process Parameters on the Inter-Layer Bond Strength of Concrete Elements Additive Manufactured by Shotcrete 3D Printing - Kruger Jacques, Plessis Anton, Zijl Gideon (2020-12)
An Investigation into the Porosity of Extrusion-Based 3D Printed Concrete - Kruger Jacques, Zijl Gideon (2020-10)
A Compendious Review on Lack-of-Fusion in Digital Concrete Fabrication - Liu Huawei, Liu Chao, Bai Guoliang, Wu Yiwen et al. (2022-04)
Influence of Pore-Defects on the Hardened Properties of 3D Printed Concrete with Coarse Aggregate - Liu Huawei, Liu Chao, Wu Yiwen, Bai Guoliang et al. (2022-06)
Hardened Properties of 3D Printed Concrete with Recycled Coarse Aggregate - Liu Chao, Wang Xianggang, Chen Yuning, Zhang Chao et al. (2021-06)
Influence of Hydroxypropyl-Methylcellulose and Silica-Fume on Stability, Rheological Properties, and Printability of 3D Printing Foam-Concrete - Moelich Gerrit, Kruger Jacques, Combrinck Riaan (2021-09)
Modelling the Inter-Layer Bond Strength of 3D Printed Concrete with Surface Moisture - Muthukrishnan Shravan, Ramakrishnan Sayanthan, Sanjayan Jay (2020-09)
Effect of Microwave-Heating on Inter-Layer Bonding and Buildability of Geopolymer 3D Concrete Printing - Nerella Venkatesh, Mechtcherine Viktor (2018-03)
Virtual Sliding-Pipe Rheometer for Estimating Pumpability of Concrete - Rahul Attupurathu, Mohan Manu, Schutter Geert, Tittelboom Kim (2021-10)
3D Printable Concrete with Natural and Recycled Coarse Aggregates:
Rheological, Mechanical and Shrinkage Behavior - Rahul Attupurathu, Santhanam Manu (2020-02)
Evaluating the Printability of Concretes Containing Lightweight Coarse Aggregates - Rushing Todd, Chaar Ghassan, Eick Brian, Burroughs Jedadiah et al. (2017-01)
Investigation of Concrete Mixtures for Additive Construction - Salet Theo, Ahmed Zeeshan, Bos Freek, Laagland Hans (2018-05)
Design of a 3D Printed Concrete Bridge by Testing - Sanjayan Jay, Nematollahi Behzad, Xia Ming, Marchment Taylor (2018-04)
Effect of Surface Moisture on Inter-Layer Strength of 3D Printed Concrete - Sanjayan Jay, Nematollahi Behzad, Xia Ming, Marchment Taylor (2021-06)
Effect of Surface Moisture on Inter-Layer Strength of 3D Printed Concrete:
Correction - Schutter Geert, Lesage Karel, Mechtcherine Viktor, Nerella Venkatesh et al. (2018-08)
Vision of 3D Printing with Concrete:
Technical, Economic and Environmental Potentials - Tao Yaxin, Lesage Karel, Tittelboom Kim, Yuan Yong et al. (2021-11)
Influence of Substrate-Surface-Roughness and Moisture-Content on Tensile Adhesion Performance of 3D Printable Concrete - Wangler Timothy, Roussel Nicolas, Bos Freek, Salet Theo et al. (2019-06)
Digital Concrete:
A Review - Weng Yiwei, Li Mingyang, Tan Ming, Qian Shunzhi (2018-01)
Design 3D Printing Cementitious Materials via Fuller-Thompson-Theory and Marson-Percy-Model - Wolfs Robert, Bos Freek, Salet Theo (2019-03)
Hardened Properties of 3D Printed Concrete:
The Influence of Process Parameters on Inter-Layer Adhesion - Wu Yiwen, Liu Chao, Liu Huawei, Zhang Zhenzi et al. (2021-07)
Study on the Rheology and Buildability of 3D Printed Concrete with Recycled Coarse Aggregates - Xiao Jianzhuang, Ji Guangchao, Zhang Yamei, Ma Guowei et al. (2021-06)
Large-Scale 3D Printing Concrete Technology:
Current Status and Future Opportunities - Xiao Jianzhuang, Lv Zhenyuan, Duan Zhenhua, Hou Shaodan (2022-03)
Study on Preparation and Mechanical Properties of 3D Printed Concrete with Different Aggregate-Combinations - Yao Hao, Xie Zonglin, Li Zemin, Huang Chuhan et al. (2021-11)
The Relationship Between the Rheological Behavior and Inter-Layer Bonding Properties of 3D Printing Cementitious Materials with the Addition of Attapulgite - Yu Shiwei, Du Hongjian, Sanjayan Jay (2020-07)
Aggregate-Bed 3D Concrete Printing with Cement-Paste Binder - Zhang Chao, Hou Zeyu, Chen Chun, Zhang Yamei et al. (2019-09)
Design of 3D Printable Concrete Based on the Relationship Between Flowability of Cement-Paste and Optimum Aggregate-Content - Zhang Xu, Li Mingyang, Lim Jian, Weng Yiwei et al. (2018-08)
Large-Scale 3D Printing by a Team of Mobile Robots
86 Citations
- Liu Chao, Chen Xianqin, Luo Zhiyu, Liu Huawei et al. (2026-01)
Effects of Pore Defects on Interfacial Bonding Between Rebar and 3D Printed Coarse Aggregate Concrete Under Multiple Loading Conditions - Ding Tao, Lian Hongqian (2026-01)
Buildability Analysis of 3D Concrete Printing:
A Finite Element Model Incorporating Segment-by-Segment Activation, Nozzle Constraint, and Extrusion Pressure - Liu Huawei, Tao Yaxin, Zhu Chao, Liu Chao et al. (2025-11)
3D Printed Concrete with Recycled Coarse Aggregate:
Freeze-Thaw Resistance Assessment and Damage Mechanisms - Xu Shuhao, Lin Xing-Tao, Chen Xiangsheng (2025-11)
Numerical Investigation of Anisotropic in 3D Printed Concrete Specimens Considering the Effects of Weak Interfaces and Pore-Induced Defects - Liu Renlong, Cheng Zhangqi (2025-10)
Interlayer Fracture Properties of 3D-Printed Cement-Based Structures:
Influencing Factors and Mechanisms - Paul Suvash, Lee Junghyun, Tay Yi, Lim Sean et al. (2025-10)
Unlocking the Sustainable Potential of 3D Concrete Printing with Large Aggregates and Steam–CO2 Curing - Luo Rui, Sun Bin, Fei Xiangpeng, Du Hongjian (2025-10)
Interlayer Strength Loss in 3D Printed Concrete Due to Time-Gap-Induced Macroporosity - Zhang Junyi, Zhang Chao, Zhang Yuying, Li Muduo et al. (2025-09)
Designing Printable Cement Composites with Porous Biochar Using an Extended Water Film Thickness Theory - Maroszek Marcin, Rudziewicz Magdalena, Hebda Marek (2025-09)
Recycled Components in 3D Concrete Printing Mixes:
A Review - Sun Hou-Qi, Zeng Jun-Jie, Xie Shan-Shan, Xia Jun-Run et al. (2025-09)
Mechanical and Microstructural Characterization of Interlayer Bonding in Multi-Material 3D-Printed Concrete - Bai Meiyan, Xiao Jianzhuang, Ding Tao, Chen Weihua (2025-09)
Integrated Non-Destructive Assessment of 3D Printed UHPC Microstructure Using X-Ray Computed Tomography and Ultrasonic Waves - Chan Li-Jing, Padil Khairul, Chin Chee-Long, Ibrahim Izni et al. (2025-09)
Strategies to Enhance Interlayer Bonding in 3D Printed Concrete:
A Review - Li Leo, Fei Zuojie, Jiao Chujie, Luo Tao et al. (2025-09)
Bauxite Residue-Based 3D Printing Mortar:
Enhancing Performance and Sustainability Through the Paste Replacement Approach - Wang Yufei, Sun Junbo, Wang Xiangyu, Huang Bo et al. (2025-09)
Environmental and Economic Evaluation of a Prefabricated 3D-Printed Structural Units Using Recycled Aggregates from Construction and Demolition Waste:
A Case Study in China - Maroszek Marcin, Hager Izabela, Mróz Katarzyna, Sitarz Mateusz et al. (2025-08)
Anisotropy of Mechanical Properties of 3D-Printed Materials:
Influence of Application Time of Subsequent Layers - Geng Shao-bo, Zhang Chen, Zhang Hui, Hai Lu et al. (2025-08)
Upcycling Coal Gangue Coarse Aggregates into 3D Printed Concrete:
Multi-Scale Mechanisms of Fracture Behaviour - Garcés Gonzalo, García-Alvarado Rodrigo, Bunster Victor, Muñoz-Sanguinetti Claudia (2025-06)
Additive Construction 4.0:
A Systematic Review of 3D Concrete Printing for Construction 4.0 - Álvarez-Fernández Martina, Guerrero-Miguel Diego-José, González-Nicieza Celestino, Prendes-Gero María et al. (2025-06)
Mortars with Mining Tailings Aggregates:
Implications for Additive Manufacturing - Song Xinlei, Xu Quanbiao, Wang Hailong, Sun Xiaoyan et al. (2025-05)
Flowability-Dependent Anisotropic Mechanical Properties of 3D Printing Concrete:
Experimental and Theoretical Study - Tao Yaxin, Zhang Yi, Mohan Manu, Dai Xiaodi et al. (2025-05)
Waste-Derived Aggregates in 3D Printable Concrete:
Current Insights and Future Perspectives - Mukhtar Faisal (2025-05)
3D-Printed Concrete Fracture:
Effects of Cohesive Laws, Mixes, and Print Parameters in 3D EXtended FEM - Demirbaş Ali, Tuğluca Merve, Şahin Oğuzhan, İlcan Hüseyin et al. (2025-05)
A Comprehensive Study on the Valorization of Recycled Concrete Aggregates in 3D-Printable Cementitious Systems - Luo Xiaoyu, Zhao Yuqi, Yao Xiaofei, Zou Cunjun et al. (2025-05)
3D Printing Concrete Interface Treatment Based on Physical and Chemical Methods:
A Review - Khanverdi Mohsen, Das Sreekanta (2025-05)
Performance of Full-Scale 3D-Printed Concrete Walls:
Effects of Vertical Reinforcements and Window Opening - Xiong Baocheng, Liu Huanbao, Nie Ping, Li Xiaoxi et al. (2025-04)
Effect of Different Surface Modification Methods of Small Particle Size Recycled Rubber Powder on Mechanical Properties of 3D Printed Concrete - Zhang Yuying, Zhu Xiaohong, Li Muduo, Zhang Chao et al. (2025-04)
3D Printing Technology in Concrete Construction - Liu Chao, Li Xin, Wu Yiwen, Liu Huawei et al. (2025-03)
Impact of External Loading on the Time-Dependent Evolution of 3D Printed Concrete with Recycled Sand in the Green State - Liu Zhenbang, Li Mingyang, Wang Xiangyu, Wong Teck et al. (2025-03)
Investigate Mechanisms of Different Printing Parameters on the Mechanical Anisotropy of 3D Concrete Printing Elements by Using Computed Tomography Scan and Computational Fluid Dynamics Methods - Liu Chao, Liang Zhan, Liu Huawei, Wu Yiwen et al. (2025-03)
Seismic Performance of 3D Printed Reinforced Concrete Walls:
Experimental Study and Numerical Simulation - Liu Chao, Liu Huawei, Wu Yiwen, Wu Jian et al. (2025-02)
Effect of X-Ray CT Characterized Pore Structure on the Freeze-Thaw Resistance of 3D Printed Concrete with Recycled Coarse Aggregate - Liu Xiongfei, Li Chuang, Guo Pei, Wang Li et al. (2025-02)
Spray-Based 3D Printed Tunnel Slag Concrete:
Evaluation for Printability and Mechanical Performance - Liu Xinhao, Hu Jiajun, Guo Xiaolu (2025-01)
Improved Interlayer-Bonding of 3D Printed Fiber-Reinforced Geopolymer by Healing-Agents:
Properties, Mechanism, and Environmental Impacts - Pepe Marco, Lombardi Rosario, Lima Carmine, Paolillo Bruno et al. (2025-01)
Experimental Evidence on the Possible Use of Fine Concrete and Brick Recycled Aggregates for 3D Printed Cement-Based Mixtures - Wang Hailong, Shen Wenbin, Sun Xiaoyan, Song Xinlei et al. (2025-01)
Influences of Particle-Size on the Performance of 3D Printed Coarse Aggregate Concrete:
Experiment, Microstructure, and Mechanism Analysis - Wang Qingwei, Han Song, Liu Qi, Yang Junhao et al. (2024-12)
Research on the 3D Printing Process and Filament Shape of Cementitious Materials in Low Gravity - Liu Huawei, Wang Yifei, Zhu Chao, Wu Yiwen et al. (2024-11)
Design of 3D Printed Concrete Masonry for Wall Structures:
Mechanical Behavior and Strength Calculation Methods Under Various Loads - Wang Qingwei, Han Song, Yang Junhao, Li Ziang et al. (2024-11)
Optimizing Printing and Rheological Parameters for 3D Printing with Cementitious Materials - Venugopal Reddy P., Nakkeeran G., Roy Dipankar, Alaneme George (2024-11)
Evaluating the Use of Recycled Fine Aggregates in 3D Printing:
A Systematic Review - Ding Yahong, Tong Jiaqi, Zhang Meixiang, Guo Shuqi et al. (2024-11)
Effect of Aggregate Gradation on the Properties of 3D Printed Recycled Coarse Aggregate Concrete - Habibi Alireza, Buswell Richard, Osmani Mohamed, Aziminezhad Mohamadmahdi (2024-11)
Sustainability Principles in 3D Concrete Printing:
Analysing Trends, Classifying Strategies, and Future Directions - Liu Bing, Guo Yazhao, Wang Yang, Liu Qizhou et al. (2024-11)
Study on the Compression Performance of 3D Printing Concrete Permanent Formwork Composite Columns - Wagner Juliana, Silveira Marcos, Vanderlei Romel, Das Sreekanta (2024-10)
Comparative Analysis of Mold-Cast and 3D Printed Cement-Based Components:
Implications for Standardization in Additive Construction - Liu Chao, Zhang Yukun, Liu Huawei, Wu Yiwen et al. (2024-10)
Inter-Layer Reinforced 3D Printed Concrete with Recycled Coarse Aggregate:
Shear Properties and Enhancement Methods - Lin Yini, Yan Jiachuan, Sun Ming, Han Xiaoyu et al. (2024-10)
Inter-Layer Cohesion in 3D Printed Concrete:
The Role of Width-to-Height-Ratio in Modulating Transport Properties and Pore-Structure - Ding Yao, Ou Xingjian, Qi Hongtuo, Xiong Gang et al. (2024-10)
Inter-Layer Bonding Performance of 3D Printed Engineered Cementitious Composites:
Rheological Regulation and Fiber Hybridization - Chen Yidong, Zhang Yunsheng, Quan Hongzhu, Liu Cheng et al. (2024-10)
Early-Age Time-Dependent Mechanical Properties of 3D Printed Concrete with Coarse Aggregates - Seo Eun-A, Lee Hojae (2024-10)
Influence of Chemical Admixtures on Buildability and Deformation of Concrete for Additive Manufacturing - Cai Jianguo, Wang Jingsong, Zhang Qian, Du Caixia et al. (2024-10)
State of the Art of Mechanical Properties of 3D Printed Concrete - Cao Jing, Shengzhao E., Yang Yi, Shi Yaming et al. (2024-09)
A Strategy for the Improvement of the Bonding Performance of 3D Printed Concrete Inter-Layer Interfaces - Ler Kee-Hong, Ma Chau-Khun, Chin Chee-Long, Ibrahim Izni et al. (2024-08)
Porosity and Durability Tests on 3D Printing Concrete:
A Review - Tittelboom Kim, Mohan Dhanesh, Šavija Branko, Keita Emmanuel et al. (2024-08)
On the Micro-and Meso-Structure and Durability of 3D Printed Concrete Elements - Fernand Muhirwa, Li Yaqi, Qian Qiwei, Chi Yin et al. (2024-08)
Effects of Coarse Aggregates on 3D Printability and Mechanical Properties of Ultra-High-Performance Fiber-Reinforced Concrete - Zhang Kaijian, Lin Wenqiang, Zhang Qingtian, Wang Dehui et al. (2024-07)
Evaluation of Anisotropy and Statistical Parameters of Compressive Strength for 3D Printed Concrete - Wu Yiwen, Liu Chao, Liu Huawei, Bai Guoliang et al. (2024-07)
Mechanism of the Influence of Multi-Scale Pore-Structure on the Triaxial Mechanical Properties of 3D Printed Concrete with Recycled Sand - Zhong Kuangnan, Huang Kaiyun, Liu Zhichao, Wang Fazhou et al. (2024-07)
CO2-Driven Additive Manufacturing of Sustainable Steel-Slag-Mortars - Bai Meiyan, Xiao Jianzhuang, Shen Jianyu, Ding Tao et al. (2024-07)
Printability and Mechanical Anisotropy of 3D Printed Concrete with Manufactured Sand Derived from Basalt - Villiers Wibke, Mwongo Mwiti, Babafemi Adewumi, Zijl Gideon (2024-06)
Quantifying Recycled Construction and Demolition Waste for Use in 3D Printed Concrete - Aslani Farhad, Zhang Yifan (2024-06)
Sustainable 3D Printed Concrete Structures Using High-Quality Secondary Raw Materials - González-Fonteboa Belén, Seara-Paz Sindy, Caneda-Martínez Laura (2024-06)
3D Printing Concrete with Byproducts - An Dong, Zhang Yixia, Yang Chunhui (2024-05)
Incorporating Coarse Aggregates into 3D Concrete Printing from Mixture Design and Process-Control to Structural Behavior and Practical Applications:
A Review - Wu Yiwen, Liu Chao, Bai Guoliang, Liu Huawei et al. (2024-05)
Effect of Time Interval on the Inter-Layer Adhesion of 3D Printed Concrete with Recycled Sand:
Multi-Factor Influencing Mechanisms and Superabsorbent Polymer Enhancement - Lyu Qifeng, Wang Yalun, Dai Pengfei (2024-05)
Multilayered Plant-Growing Concrete Manufactured by Aggregate-Bed 3D Concrete Printing - Wei Ying, Han Song, Yu Shiwei, Chen Ziwei et al. (2024-05)
Parameter Impact on 3D Concrete Printing from Single to Multi-Layer Stacking - Sun Bochao, Dominicus Randy, Dong Enlai, Li Peichen et al. (2024-04)
Predicting the Strength Development of 3D Printed Concrete Considering the Synergistic Effect of Curing-Temperature and Humidity:
From Perspective of Modified Maturity-Model - Lu Yue, Xiao Jianzhuang, Li Yan (2024-03)
3D Printing Recycled Concrete Incorporating Plant-Fibers:
A Comprehensive Review - Xiong Baocheng, Nie Ping, Liu Huanbao, Li Xiaoxi et al. (2024-03)
Optimization of Fiber-Reinforced Lightweight Rubber-Concrete Mix-Design for 3D Printing - Jaji Mustapha, Zijl Gideon, Babafemi Adewumi (2024-03)
Durability and Pore-Structure of Metakaolin-Based 3D Printed Geopolymer Concrete - Xiao Jianzhuang, Bai Meiyan, Wu Yuching, Duan Zhenhua et al. (2024-01)
Inter-Layer Bonding Strength and Pore Characteristics of 3D Printed Engineered Cementitious Composites - Rocha Douglas, Faria Paulina, Lucas Sandra (2023-12)
Additive Manufacturing of Earth-Based Materials:
A Literature Review on Mortar-Composition, Extrusion, and Processing Earth - Wang Li, Wang Fucheng, Li Rong, Wang Qiao (2023-12)
Interfacial Constitutive Model of 3D Printed Fiber-Reinforced Concrete Composites and Its Experimental Validation - Warsi Syed, Srinivas Dodda, Panda Biranchi, Biswas Pankaj (2023-12)
Investigating the Impact of Coarse Aggregate Dosage on the Mechanical Performance of 3D Printable Concrete - Liu Huawei, Liu Chao, Zhang Yamei, Bai Guoliang (2023-11)
Bonding Properties Between 3D Printed Coarse Aggregate Concrete and Rebar Based on Interface Structural Characteristics - Lyu Qifeng, Dai Pengfei, Zong Meirong, Zhu Pinghua et al. (2023-10)
Plant-Germination Ability and Mechanical Strength of 3D Printed Vegetation Concrete Bound with Cement and Soil - Rui Aoyu, Wang Li, Lin Wenyu, Ma Guowei (2023-10)
Experimental Study on Damage Anisotropy of 3D Printed Concrete Exposed to Sulfate-Attack - Rudziewicz Magdalena, Maroszek Marcin, Góra Mateusz, Dziura Paweł et al. (2023-09)
Feasibility Review of Aerated Materials Application in 3D Concrete Printing - Yang Huashan, Che Yujun, Luo Jie (2023-08)
Calcium Leaching of 3D Printed Cement-Paste Exposed to Ammonium Chloride Solutions - Wang Yang, Qiu Liu-Chao, Hu Yan-Ye, Cheng Song-Gui et al. (2023-08)
Influential Factors on Mechanical Properties and Microscopic Characteristics of Underwater 3D Printing Concrete - Zhu Lingli, Zhang Meng, Zhang Yaqi, Yao Jie et al. (2023-07)
Research Progress on Shrinkage Properties of Extruded 3D Printed Cement-Based Materials - Wang Chaofan, Chen Bing, Vo Thanh, Rezania Mohammad (2023-07)
Mechanical Anisotropy, Rheology and Carbon Footprint of 3D Printable Concrete:
A Review - Xu Zhuoyue, Zhang Dawang, Li Hui, Yin Le et al. (2023-06)
Effects of Additives on the Mechanical Properties, Rheology, and Printing Properties of PCC-Based 3DPMs - Wang Li, Ye Kehan, Wan Qian, Li Zhijian et al. (2023-05)
Inclined 3D Concrete Printing:
Build-Up Prediction and Early-Age Performance-Optimization - Zbyszyński Wojciech, Pietras Daniel, Sadowski Tomasz (2023-04)
Data-Image-Correlation-Analysis of the Destruction-Process of 3D Printable Layered Beams Subjected to the Three-Point Bending Process - Chen Yidong, Zhang Wenhua, Zhang Yunsheng, Zhang Yu et al. (2023-03)
3D Printed Concrete with Coarse Aggregates:
Built-In-Stirrup Permanent Concrete Formwork for Reinforced Columns - Fonseca Mariana, Matos Ana (2023-03)
3D Construction Printing Standing for Sustainability and Circularity:
Material-Level Opportunities - Xiao Jianzhuang, Hou Shaodan, Duan Zhenhua, Zou Shuai (2023-01)
Rheology of 3D Printable Concrete Prepared by Secondary Mixing of Ready-Mix Concrete - Raphael Benny, Senthilnathan Shanmugaraj, Patel Abhishek, Bhat Saqib (2023-01)
A Review of Concrete 3D Printed Structural Members
BibTeX
@article{liu_liu_wu_bai.2022.3PCwRCA,
author = "Huawei Liu and Chao Liu and Yiwen Wu and Guoliang Bai and Chunhui He and Yizhou Yao and Rongfei Zhang and Youqiang Wang",
title = "3D Printing Concrete with Recycled Coarse Aggregates: The Influence of Pore-Structure on Inter-Layer Adhesion",
doi = "10.1016/j.cemconcomp.2022.104742",
year = "2022",
journal = "Cement and Concrete Composites",
volume = "134",
}
Formatted Citation
H. Liu, “3D Printing Concrete with Recycled Coarse Aggregates: The Influence of Pore-Structure on Inter-Layer Adhesion”, Cement and Concrete Composites, vol. 134, 2022, doi: 10.1016/j.cemconcomp.2022.104742.
Liu, Huawei, Chao Liu, Yiwen Wu, Guoliang Bai, Chunhui He, Yizhou Yao, Rongfei Zhang, and Youqiang Wang. “3D Printing Concrete with Recycled Coarse Aggregates: The Influence of Pore-Structure on Inter-Layer Adhesion”. Cement and Concrete Composites 134 (2022). https://doi.org/10.1016/j.cemconcomp.2022.104742.